Description
Motorola (Emerson) MVME5500-0161 6U VME64 Single Board Computer, MPC7457 PowerPC Processor, Dual PMC Slots, Real-Time Embedded CPU Board

MVME5500-0161
Technical Specifications
- Catalog Number: MVME5500-0161
- Brand: Motorola / Emerson Network Power (now Artesyn / Advanced Energy)
- Form Factor: 6U VMEbus single slot SBC, VME64 (ANSI/VITA 1-1994)
- Processor: MPC7457 PowerPC @ 1 GHz with AltiVec SIMD engine
- Cache: 32 KB I / 32 KB D L1, 512 KB on-chip L2, 2 MB L3 cache
- Memory: 512 MB soldered ECC SDRAM (133 MHz)
- Flash: 40 MB total (32 MB bank + 8 MB bank, write-protect jumper)
- NVRAM: 32 KB battery-backed, 4 KB user-accessible
- I/O Interfaces:
- 1 × Gigabit Ethernet (1000Base-T)
- 1 × 10/100Base-TX Ethernet
- 2 × Asynchronous serial ports (RS232 / EIA‑530 configurable)
- Expansion: 2 × PMC (PCI Mezzanine Card) sites, dual 64-bit PCI bus up to 66 MHz
- VMEbus: VME64 master/slave, DMA support
- Onboard Peripherals: 8 × 32-bit timers, watchdog timer, TOD real-time clock
- Supported OS: VxWorks, Linux, QNX
- Operating Temperature: 0 °C ~ +70 °C commercial; rugged variant -40 °C ~ +85 °C
- Supply: +5 V, ±12 V via VME backplane
- Lifecycle Status: Discontinued / Obsolete; last time buy closed, only tested spare & repair available
- Certifications: CE, industrial EMC
Key Features & Advantages
- High-performance PowerPC architecture with AltiVec: Optimised for floating-point, signal processing and real-time closed-loop computation.
- ECC protected main memory: Detects and corrects single-bit memory errors, critical for long-run unattended embedded systems.
- Dual independent PMC expansion sites: Flexibly add fieldbus, analog I/O, high-speed serial, MIL-STD-1553 or frame grabber mezzanine cards.
- Dual Ethernet networking: Segmented control network and data logging network without external switches.
- Deterministic VME64 bus interface: Reliable backplane communication with legacy VME I/O racks widely deployed in test, defence and accelerator systems.
- Battery-backed NVRAM and RTC: Preserves calibration parameters, IP settings and timestamp across power cycles.
- Software programmable watchdog timer: Automatic system reset on software hang for high-availability setups.
- Drop-in compatibility with MVME51xx family: Reduces migration effort for existing VME chassis and software stacks.
Application Fields
- Industrial real-time control and VME-based test systems
- Aerospace, defence and radar data processing racks
- Particle accelerator, beamline control and scientific instrumentation
- Offshore and marine embedded control systems
- Medical imaging and diagnostic equipment
- Railway signalling and vehicle control electronics
- Legacy simulation, motion control and hydraulic test benches
- Retrofit replacement for existing MVME5500 installed base
Related Product Recommendations
- MVME5500-0163: Alternative memory / flash variant of MVME5500 series
- MVME55006E: Extended temperature rugged version
- MVME5100: Lower performance compatible VME SBC (drop-in software compatible)
- MVME6100: Later generation PowerPC VME CPU
- PMC-GigE: PMC gigabit Ethernet mezzanine
- PMC-ARINC429 / PMC-1553: Avionics interface PMC cards
- VME64 backplane chassis, 6U card cage
- VxWorks BSP package for MVME5500
- MVME2400 / MVME3100: Older legacy Motorola VME SBCs
- VPX single board computers: Modern open-standard upgrade platform
Installation & Maintenance
Installation
- Insert the 6U board carefully into the VME chassis guide rails, seat firmly into the backplane connector and fasten front panel ejector latches.
- Confirm backplane voltage levels (+5 V, ±12 V) before applying power; avoid hot insertion unless chassis supports hot-swap.
- Configure serial port mode, boot source and flash write protection via on-board jumpers before boot.
- Assign unique VMEbus address and interrupt level to avoid bus conflicts with other VME modules.
- Route Ethernet and serial cables away from high-current VME power lines to minimise EMI; use shielded cables for serial links.
- Install PMC mezzanine cards only when power is removed; verify PMC cooling clearance and mechanical interference.
- Set up network partitioning: gigabit port for high-volume data, 10/100 port for control and diagnostics.
- Load matching VxWorks/Linux BSP and preserve boot parameters in non-volatile storage.
Maintenance
- Perform periodic visual inspection of front panel connectors, ejector latches and battery condition; NVRAM battery has limited service life.
- Run memory ECC test, VME bus read/write test and watchdog functional test during scheduled outages.
- Backup boot image, startup script and application configuration to external storage regularly.
- This model is obsolete; maintain fully tested spare boards for critical racks, as factory repair support is limited.
- If communication instability occurs, inspect backplane pins, clean edge connectors with approved contact cleaner and check chassis ground bonding.
- Do not remove heatsink; the processor and AltiVec core are sensitive to overheating.
- After replacement, re-validate VME interrupt mapping, PMC resource allocation and network settings before returning to operation.
- Keep BSP version, boot log and bus topology records for system audit and troubleshooting.


