Allen‑Bradley 1794-IRT8XT | FLEX I/O-XT 8-Ch Thermocouple / RTD / mV Analog Input Module

  1. 1794-IRT8 – Standard temp 8ch TC/RTD/mV module (non XT)
  2. 1794-IT8XT – XT 8ch thermocouple / mV input
  3. 1794-IR8XT – XT 8ch RTD only input
  4. 1794-IE8XT – XT 8-channel single-ended analog input
  5. 1794-OE4XT – XT 4-channel analog output
  6. 1794-IE12 – 12-channel analog input (standard)
  7. 1794-IF8IHNFXT – XT HART 8ch analog input
  8. 1794-OB16PXT – XT 16-point digital output
  9. 1794-OW8XT – XT 8-point relay output
  10. 1794-IB16XT – XT 16-point digital input
  11. 1794-AENTRXT – XT Ethernet/IP FLEX adapter
  12. 1794-ACN15XT – XT ControlNet FLEX adapter
  13. 1794-OF8IH – HART analog output module
  14. 1794-IE4XOE2XT – XT mixed 4-in / 2-out analog
  15. 1794-NM1 – Panel mount kit for FLEX terminal base

 

Category: SKU: Allen 1794-IRT8XT Brand:

Description

Allen‑Bradley 1794-IRT8XT | FLEX I/O-XT 8-Ch Thermocouple / RTD / mV Analog Input Module

 

Product Description

1794-IRT8XT is a conformal-coated, extended-temperature FLEX I/O-XT analog input module manufactured by Rockwell Automation. It provides 8 universal single-ended channels to read thermocouple, 2/3/4-wire RTD, and millivolt signals for temperature monitoring. It supports open-wire detection, over/under-range diagnostics and cold-junction compensation for thermocouple applications. The XT variant features conformal coating and wider ambient temperature range than standard 1794-IRT8, designed for harsh industrial environments with humidity, dust, vibration and broad temperature swings. It works within the FLEX I/O distributed remote I/O system and communicates to Logix controllers via FLEX adapter over ControlNet, DeviceNet or Ethernet/IP. This part is active mature lifecycle, widely used for process temperature acquisition in heavy industrial sites.

 

Technical Specifications

 

Item Parameter
Part Number 1794-IRT8XT
Manufacturer Allen‑Bradley (Rockwell Automation)
Series FLEX I/O-XT
Channel Count 8 universal analog input channels, single-ended
Signal Types Thermocouple (multiple types), 2/3/4-wire RTD, millivolt
Resolution 16-bit
Power Supply 24VDC, 19.2–31.2VDC range
Operating Temperature -20℃ ~ +70℃
Conformal Coating Yes (XT version)
Diagnostics Open sensor wire, over-range, under-range, module fault
Cold Junction Compensation Built-in, CJC accessories included
Backplane Bus FLEXbus
Mounting DIN 35mm rail via terminal base
Protection IP20 (module + terminal base assembly)
Humidity 5~95% RH non-condensing
Origin Singapore
Warranty 1 Year

 

Compatibility & Installation Pitfalls

Compatibility

  • Adapter: FLEX I/O adapters (1794-ACN15, 1794-ADN, 1794-AENT, 1794-AENTR, XT adapter variants)
  • Terminal Base: 1794-TB2, TB3, TB3S, TB3T, TB3TS terminal bases
  • Controller Family: ControlLogix, CompactLogix, PLC-5, SLC500 with block transfer capability
  • Software: Studio5000 / RSLogix5000, RSNetworx for DeviceNet / ControlNet
  • Variant note: 1794-IRT8 (standard temp range, no conformal coating); 1794-IRT8XT = extended temp + conformal coating

Critical Installation Pitfalls

  1. External 24VDC power requirement: Module is not powered by FLEXbus backplane. 24VDC field supply must be wired to terminal base; missing supply causes module to appear empty to adapter.
  2. Non-isolated inputs: All 8 channels share common reference. Ground loops will introduce temperature reading drift. Separate grounding rules mandatory for thermocouple wiring.
  3. Terminal base keying: Must set terminal base keyswitch to position 3. Wrong key position prevents proper module seating or causes hardware damage.
  4. Hot insertion risk: Do not plug/unplug module while rack energized, especially hazardous classified locations; arcing risk.
  5. Thermocouple wiring rules: Use dedicated thermocouple extension wire, avoid copper wire substitution. Improper wire material creates cold junction error and inaccurate temperature readings.
  6. RTD wiring resistance error: 2-wire RTD has lead resistance offset; use 3 or 4-wire configuration for high precision temperature measurement.
  7. Conformal coating handling: XT coated module cannot have coating scratched or stripped; damage reduces protection against corrosive humid environment.
  8. Series A / Series B behaviour difference: Series B changes fault value when sensor wire breaks. Mixing old A-series and new B-series modules in same node can create inconsistent fault handling logic.

 

Standard Operating Procedure (SOP)

1. Pre-Installation Inspection & LOTO

  • Verify catalog number 1794-IRT8XT, inspect module housing, connector pins for scratch or coating damage.
  • Lockout/Tagout 24VDC power to terminal base; confirm power de-energized.
  • Check terminal base key switch, Flexbus interconnector continuity.
  • Prepare thermocouple/RTD shielded cable, Studio5000 project backup, CJC cold junction parts.

2. Mechanical Mounting

  • Mount selected 1794 terminal base onto DIN35 rail.
  • Rotate keyswitch to position 3 for universal temperature module.
  • Fully extend Flexbus connector to link adjacent terminal bases / adapter.
  • Align module with terminal base groove, press evenly until latch locks.
  • Maintain side clearance for convection cooling.

3. Field Wiring

  • Wire 24VDC supply to terminal base power terminals.
  • Route thermocouple / RTD / mV sensor cables; use thermocouple-grade extension wire for TC.
  • Separate low-level temperature signal wiring away from high-power motor cables.
  • Configure wiring topology: 2/3/4 wire for RTD according to accuracy requirement.
  • Complete cold junction compensation setup. Double-check polarity.

4. Power-Up & Commissioning

  • Restore 24VDC power, check module LED status.
  • In Studio5000, add 1794-IRT8XT module profile, define each channel signal type (TC type / RTD / mV).
  • Download project to controller, establish FLEX adapter communication.
  • Verify each channel raw value, check open-wire / range fault diagnostics.
  • Compare readings with reference calibrator; tune cold junction compensation if offset exists.
  • Validate alarm triggers for sensor break and out-of-range signals.

5. Maintenance & Replacement

  • Periodically inspect terminal tightness, dust buildup, cabinet temperature and humidity.
  • Replacement procedure: Execute LOTO, remove old module, install new 1794-, confirm key setting, reload module channel configuration, re-verify all temperature channels.
  • Troubleshooting: Check wiring continuity, common-mode noise, 24V supply stability and open-wire fault flags.

 

Application Scenarios

  1. Petrochemical, refinery and chemical plant temperature monitoring
  2. Power plant boiler, turbine and auxiliary process temperature measurement
  3. Food & beverage batch thermal control and oven temperature profiling
  4. HVAC, water treatment and industrial furnace temperature acquisition
  5. Heavy machinery, mining and offshore auxiliary temperature monitoring (harsh environment, wide temperature range)

 

Supporting / Matching Components

  1. 1794 series FLEX I/O Adapter (1794-AENTR, 1794-ACN15, 1794-ADN)
  2. 1794-TB3 / TB3S / TB3T terminal base unit
  3. Thermocouple extension wire, shielded twisted pair for RTD
  4. 24VDC field power supply
  5. CJC cold junction compensation accessories
  6. DIN 35mm rail and cabinet grounding bar
  7. Studio5000 / RSLogix5000 programming software
  8. Calibrator for temperature sensor loop checking
  9. ESD wrist strap
  10. FLEXbus interconnection cables

 

15 Recommended Same-Series / Compatible FLEX I/O XT Models

  1. 1794-IRT8 – Standard temp 8ch TC/RTD/mV module (non XT)
  2. 1794-IT8XT – XT 8ch thermocouple / mV input
  3. 1794-IR8XT – XT 8ch RTD only input
  4. 1794-IE8XT – XT 8-channel single-ended analog input
  5. 1794-OE4XT – XT 4-channel analog output
  6. 1794-IE12 – 12-channel analog input (standard)
  7. 1794-IF8IHNFXT – XT HART 8ch analog input
  8. 1794-OB16PXT – XT 16-point digital output
  9. 1794-OW8XT – XT 8-point relay output
  10. 1794-IB16XT – XT 16-point digital input
  11. 1794-AENTRXT – XT Ethernet/IP FLEX adapter
  12. 1794-ACN15XT – XT ControlNet FLEX adapter
  13. 1794-OF8IH – HART analog output module
  14. 1794-IE4XOE2XT – XT mixed 4-in / 2-out analog
  15. 1794-NM1 – Panel mount kit for FLEX terminal base

 

FAQ

  • Q: What is difference between 1794-IRT8 and 1794-? A: The XT version has conformal coating and extended temperature range -20 ~ +70°C for harsh environment. Standard 1794-IRT8 is 0~60°C without coating. Pinout, channel function and terminal base are identical.
  • Q: Can I use regular copper wire for thermocouple input? A: No. Copper wire introduces cold junction error. Use matching thermocouple extension cable.
  • Q: Does module draw power over FLEXbus? A: No. 24VDC must be supplied to terminal base separately. FLEXbus only handles data communication.
  • Q: Are input channels galvanically isolated? A: No, inputs are non-isolated single-ended design. Ground loops will affect measurement precision.