VE4003S6B1 Product Introduction

  • M‑Series carrier and RTD termination block 12P1811X032
  • VE4003S2B1 (8‑ch HART 4‑20mA AI, your prior item)
  • VE4003S5B1 (Thermocouple input module)
  • DeltaV controllers and EIOC interface assemblies

 

Category: SKU: VE4003S6B1 Brand:

Description

VE4003S6B1 Product Introduction

 

Overview

The VE4003S6B1 is an Emerson DeltaV M‑Series 8‑channel RTD resistance temperature detector input module, alternate part number KJ3225X1‑BA2 / KJ3002X1‑BF1. It is dedicated to acquiring temperature signals from platinum RTD sensors, converting resistance readings into precise temperature values for the DeltaV DCS. This legacy M‑Series I/O card is OEM end‑of‑life and widely supplied as surplus or refurbished spare for outage maintenance and lifecycle extension of existing DeltaV installations.

VE4003S6B1

Key Features & Benefits

  • 8 isolated RTD input channels, supporting 2‑wire, 3‑wire and 4‑wire RTD sensor wiring
  • High‑precision resistance measurement for Pt100, Pt1000 and other standard RTD types
  • Built‑in wire break detection and per‑channel fault LEDs for fast on‑site troubleshooting
  • Channel‑to‑backplane isolation to reduce ground loop interference and protect control circuitry
  • Hot‑swappable on matching M‑Series carrier assembly; replacement without rack shutdown
  • Conformal coated PCB, meets ISA G3 corrosion standard for power, oil & gas and chemical cabinets
  • Configured, calibrated and diagnosed directly via DeltaV Explorer software
  • Optimized for continuous temperature monitoring and over‑temperature interlock protection

 

Technical Specifications

Item Description
Manufacturer Emerson
Model VE4003S6B1
Alternate PN KJ3225X1-BA2, KJ3002X1-BF1
Type 8‑Channel RTD Temperature Input Module
Compatible System DeltaV DCS M‑Series Traditional I/O
Sensor Type 2/3/4‑wire RTD (Pt100, Pt1000)
Communication DeltaV Local Bus
Power 12 VDC from M‑Series carrier
Isolation Channel‑to‑backplane isolation
Termination Assembly 12P1811X032 RTD terminal block
Operating Temperature -40°C ~ +70°C
OEM Status Discontinued, available as surplus / refurbished spare
Application Temperature monitoring, furnace, turbine, reactor and heat process loops

 

Typical Applications

VE4003S6B1 is used to capture critical temperature measurements from RTD probes in power plants, refineries and chemical facilities. Common uses include bearing temperature, motor winding temperature, boiler tube temperature, exhaust temperature and process vessel temperature monitoring. It is a high‑demand spare for planned outages and obsolescence replacement for DeltaV M‑Series racks.

 

Matching Companion Modules

  • M‑Series carrier and RTD termination block 12P1811X032
  • VE4003S2B1 (8‑ch HART 4‑20mA AI, your prior item)
  • VE4003S5B1 (Thermocouple input module)
  • DeltaV controllers and EIOC interface assemblies

 

Operation Notes

It belongs to M‑Series I/O and is not mechanically compatible with S‑Series carriers. Verify carrier hardware, DeltaV firmware revision and termination wiring before swap. After installation, download configuration and validate sensor type, wire mode and open‑circuit diagnostics per Emerson service manual.

 

FAQ

Q: Can VE4003S6B1 replace VE4003S2B1 directly? A: No. VE4003S2B1 is 4–20mA HART analog input, while VE4003S6B1 is RTD temperature input. Signal front‑ends are different and cannot be cross‑swapped.

Q: Can it read thermocouple signals? A: No. For thermocouple inputs, select VE4003S5B1 instead.

Q: Is it compatible with GE Speedtronic Mark V / VI / VIe? A: No. It is Emerson DeltaV native I/O and has no direct interoperability with GE turbine control platforms.