Description
Rexroth Indramat DKC02.3-100-7-FW (Order No. R911279430), ECODRIVE03 SERCOS Servo Drive, 100A Output
Core Product Introduction
The DKC02.3-100-7-FW is a high-current modular servo drive from the Bosch Rexroth Indramat ECODRIVE03 DKC family. It is designed for high-performance multi-axis motion control via SERCOS interface, supporting velocity, position and torque control for Indramat synchronous servo motors. This high-power 100A variant is widely deployed on heavy-duty machine tools, metal forming presses, injection molding, printing and textile main-axis applications. It uses a shared DC-bus architecture, supports external braking resistor modules and accepts incremental / absolute encoder feedback. It is a legacy series, mainly supplied as spare replacement for existing production lines.

Main Technical Specifications
| Item | Parameter |
|---|---|
| Part Number | DKC02.3-100-7-FW |
| Rexroth Order Code | R911279430 |
| Series | ECODRIVE03 DKC02.3 |
| Input Voltage | 200–480 VAC, 1/3 phase, 50/60 Hz |
| Rated Output Current | 100 A (3-phase) |
| Nominal DC Bus | 700 VDC |
| Control Supply | 24 VDC |
| Communication | SERCOS fiber interface |
| Feedback Types | Incremental encoder, absolute encoder |
| Control Modes | Position, velocity, torque |
| Protection | Overcurrent, overvoltage, undervoltage, overtemperature, short circuit |
| Enclosure Rating | IP20 |
| Operating Temperature | 0 °C ~ +45 °C |
| Max Installation Altitude | ≤1000 m |
| Humidity | 5%–95% RH, non-condensing |
| Mounting | DIN rail / cabinet backplate mounting |
| Weight | 9.7 kg |
| Certifications | CE, UL |
| Lifecycle Status | EOL, spare stock only |
Quality Control Procedure
- Visual & Label Inspection: Verify original Rexroth Indramat marking, part number DKC02.3-100-7-FW, serial number, power terminals, SERCOS fiber port, encoder connector; no burn marks, bent pins or corrosion.
- 24V Control Power Boot Test: Apply 24VDC control supply, confirm power LED, self-diagnostic sequence, no abnormal heating or standby current.
- DC Bus Charging & Pre-charge Test: Test mains pre-charge circuit, confirm smooth DC-bus build-up without alarm.
- SERCOS Communication Test: Connect SERCOS master, verify fiber link establishment, drive identification and parameter upload.
- Encoder Feedback Channel Test: Pair with Indramat servo motor encoder, verify position tracking and zero point reading.
- Current Loop & Output Test: Run low-current commissioning test; validate three-phase output balance and current regulation.
- Fault Alarm Simulation: Trigger over-temperature, overvoltage and external enable faults to confirm correct fault codes and safe shutdown.
- Brake / Braking Resistor Interface Check: Verify braking transistor and external BZM module interface.
- Firmware Compatibility Check: Confirm firmware version matches customer machine project and SERCOS master.
- Packaging & Traceability: Anti-static packaging, foam cushioning, serial-number linked QC report before shipment.
Frequently Asked Questions (FAQ)
Q1: What does “-FW” stand for in the part number?A1: FW means Firmware, the hardware base unit; the dedicated ECODRIVE firmware file must be loaded separately.
Q2: Is SERCOS the only communication?A2: Yes, this DKC02.3-7 variant uses SERCOS fiber bus. It does not support Profibus, Profinet or EtherNet/IP natively.
Q3: What is the difference between .3-100-7-FW and .3-040-7-FW?A3: They share the same series and firmware platform; only the power stage rated current differs (100A vs 40A). Not plug-and-play replacement without reviewing motor current and bus load.
Q4: Can I use it with non-Indramat servo motors?A4: Not recommended. Tuning tables, encoder interfaces and motor pole data are optimized for Indramat motors. Third-party motors require deep parameter tuning and risk unstable operation.
Q5: Does it include braking resistor?A5: No. External BZM/CZM braking resistor modules are ordered separately for regenerative energy dissipation.
Q6: Can I replace .3 with the newer Rexroth IndraDrive?A6: IndraDrive is the successor. It has different hardware, bus protocol and mounting; the program, wiring and SERCOS master must be fully migrated.
Installation & Configuration Guide
- Pre-install Preparation: 200–480VAC mains, 24VDC control supply, SERCOS fiber cable, Indramat servo motor, encoder cable, braking resistor module (BZM), drive commissioning software.
- Cabinet Layout & Clearance: Mount on backplate, maintain vertical airflow clearance, separate power and feedback wiring.
- Wiring: Connect mains input, DC bus link (for multi-drive shared bus), 24V control, motor power cable, encoder feedback, enable and safe-stop signals.
- SERCOS Fiber Connection: Terminate SERCOS fiber ring, ensure correct Tx/Rx direction.
- Power Up: Switch on 24V control first, then mains supply. Check no hardware fault codes.
- Firmware Loading: Load matching ECODRIVE firmware if required.
- Motor Identification & Auto-tune: Set motor code, run auto-identification for resistance, inductance and encoder offset.
- SERCOS Axis Mapping: Assign axis address, map control words, setpoint and actual-value channels in SERCOS master controller.
- Commissioning Test: Jog motor in velocity mode first, then position mode; test homing, limit switches and emergency stop.
- Backup: Save parameter set, firmware version and fault history to machine archive.
Warning: High DC bus voltage exists inside even after mains power off; observe discharge waiting time. SERCOS fiber direction reversal will cause communication failure.
Related Rexroth ECODRIVE03 DKC Series Models & Accessories (15 pcs)
| Model | Order Number | Description |
|---|---|---|
| 40A SERCOS Drive | .3-040-7-FW | ECODRIVE03 40A servo controller |
| 25A SERCOS Drive | .3-025-7-FW | .3 25A variant |
| 16A SERCOS Drive | .3-016-7-FW | .3 16A small axis drive |
| Braking Resistor Module | BZM01.1-010-00 | External brake chopper resistor unit |
| SERCOS Fiber Cable | IKS01.1-08 | SERCOS optical fiber jumper |
| Encoder Cable Kit | RKG4200 | Indramat motor feedback cable |
| Power Cable | RKL4302 | Motor power cable for DKC drives |
| ECODRIVE Commissioning Software | FWA-ECODR3-SMT | ECODRIVE firmware package |
| Indramat 100A Servo Motor | MHD112D-024-NG0-BN | Matching high-current servo motor |
| Indramat 40A Servo Motor | MHD090B-035-NG0-UN | Medium size servo motor |
| Line Filter | NFD03.1-480-00 | EMC mains line filter |
| Line Reactor | NDR02.1-480-01 | AC line reactor |
| SERCOS Master Card | Sercos III PCI card | PC-based SERCOS commissioning adapter |
| DKC Fan Replacement Kit | FAN-.3 | Cooling fan spare for high-current DKC |
| IndraDrive Replacement Drive | HCS03.1E-W0100-A-05-NNBV | New generation IndraDrive 100A |
