MTL831B, Eaton MTL830 Series IS Analogue Multiplexer Transmitter for Zone 0 hazardous area temperature / mV multiplexing

Model Order Number Description
Matching receiver MTL838B-MBF Safe area Modbus receiver
Digital isolator MTL3052 IS highway isolator between hazardous & safe side
New generation transmitter MTL831C Successor of MTL831B (full system replacement)
New generation receiver MTL838C Matching receiver for MTL831C
New isolator MTL5553 Isolator for MTL831C system
Enclosure ENC8 Standard IP67 enclosure for MTL831B
Large enclosure ENC83 Larger IP67 enclosure
Receiver enclosure ENC83SS Safe-side enclosure for MTL838B-MBF
Configuration software PCS83 Software for MTL830 series setup
Highway twisted pair cable MTL-IS-CABLE IS twisted pair highway cable
Terminal spare kit MTL831B-TERM Spare terminal block set
Surge protector MTL7787+ Temperature signal surge barrier
MTL830 manual MTL830-MAN System installation manual
Modbus cable MTL-MODBUS-CAB RS485 cable for MTL838B-MBF
MTL4041 MTL4041 RTD isolator (standalone single channel)
Category: SKU: MTL831B, MTL830 Brand:

Description

MTL831B, Eaton MTL830 Series IS Analogue Multiplexer Transmitter for Zone 0 hazardous area temperature / mV multiplexing

 

Core Product Introduction

The MTL831B is an intrinsically safe analogue multiplexer transmitter from Eaton MTL, designed for multi-point temperature measurement in hazardous locations. It accepts mixed sensor inputs: up to 16 thermocouple / millivolt inputs, or up to 15 RTD inputs (2/3/4-wire). It is powered via the twisted-pair data highway (no separate local power supply in hazardous zone) and transmits digitised sensor data to the safe-area receiver MTL838B-MBF. It supports dual redundant highway for high availability. The system requires an MTL3052 digital isolator installed in the safe side between highway and receiver. Widely used for oil & gas, refinery, chemical plant bulk temperature monitoring on reactors, pipelines and storage tanks. This model is obsolete / EOL; the matched replacement family is MTL831C + MTL838C (full system replacement required, cannot swap only single card)Eaton.

MTL831B

Main Technical Specifications

Item Parameter
Part Number MTL831B
Manufacturer Eaton MTL (UK)
Series MTL830 multiplexer system
Input capacity 16 × TC / mV; OR 15 × RTD (2/3/4-wire, mixed inputs allowed)
Safety certification Ex ia IIC T4, ATEX / FM / CSA, suitable for Zone 0 / Class I Div 1
Power Loop-powered from data highway, no field power supply
Communication Single twisted-pair data highway, dual redundant highway ports
Max cable length Up to 3 km (depends on cable & noise environment)
Matching receiver MTL838B-MBF (Modbus RS422/RS485 output)
Required isolator MTL3052 (safe-area digital isolator)
Typical accuracy ±0.1% of reading
Operating temperature -20 °C ~ +60 °C
Storage temperature -40 °C ~ +80 °C
Mounting DIN rail inside ENC8 / ENC83 IP67 enclosure
Weight ~1.3 kg
Lifecycle Status Obsolete / EOL, spare stock only
Certifications ATEX, FM, CSA, CE

 

Quality Control Procedure

  1. Visual & Label Inspection: Verify original MTL marking, MTL831B part number, serial sticker, terminal block integrity, no burn tracks or corrosion.
  2. Highway Power Boot Test: Power via MTL838B-MBF highway, confirm power and status LED, no overheating.
  3. Input Mode Configuration: Set each channel via on-board DIP switch: TC/mV or 2/3/4-wire RTD.
  4. TC / mV Calibration Test: Inject precision millivolt signal, check reading accuracy.
  5. RTD Simulation Test: Use precision resistance box to simulate RTD, verify temperature reading.
  6. Dual Redundant Highway Test: Switch between primary / secondary highway channel, verify seamless data transfer.
  7. System Link Test: Pair with MTL3052 isolator + MTL838B-MBF, confirm Modbus data output at receiver.
  8. Open-circuit / sensor fault simulation: Check fault flag and diagnostic status reported on receiver.
  9. Intrinsic safety parameter check: Confirm Ex ia entity parameters match certificate.
  10. Packaging & Traceability: Anti-static packaging, foam protection, serial-number QC report before shipment.

 

Frequently Asked Questions (FAQ)

Q1: Can MTL831B work alone without MTL838B-MBF and MTL3052?A1: No. It is a transmitter-only device. The complete system = MTL831B (hazardous area) + MTL3052 isolator + MTL838B-MBF Modbus receiver (safe area).

Q2: Can I replace with MTL831C directly?A2: No. MTL831C uses different highway protocol and hardware. You must replace the entire system: transmitter, isolator and receiver together. One-for-one card swap is not supportedEaton.

Q3: What sensors are not supported?A3: 4–20mA transmitters are not supported. It is dedicated for thermocouple, mV and RTD temperature sensors.

Q4: What software configures the system?A4: PCS83 software, used on the safe side with to set channel types, addresses and scaling.

Q5: Is hot swap supported in hazardous area?A5: Hardware can be removed, but Zone 0 work requires hot work permit and site hazardous area lockout procedures; all temperature monitoring points will be lost during replacement.

Q6: Why dual highway ports?A6: Redundancy: if one twisted-pair cable fails, the second highway keeps transmitting temperature data to the receiver.

 

Installation & Configuration Guide

  1. Pre-install Preparation: , MTL3052 isolator, receiver, shielded twisted pair highway cable, PCS83 configuration software.
  2. Enclosure Mounting: Install into IP67 ENC8/ENC83 enclosure, locate close to field temperature sensors.
  3. Field Sensor Wiring: Wire TC or RTD sensors to input terminals, separate low-level sensor cables from high-power VFD cables.
  4. Highway Wiring: Run twisted pair highway from to isolator (safe side), then to .
  5. DIP Switch Setup: Set each channel for TC / mV / 2/3/4-wire RTD.
  6. Power up the receiver: The receiver supplies power over the highway to the .
  7. PCS83 Connection: Connect PC to , scan multiplexer, assign channel tags and scaling.
  8. Modbus mapping: Map all temperature values and channel fault status into Modbus registers for DCS/PLC.
  9. Fault test: Disconnect one sensor, confirm fault bit appears on Modbus.
  10. Backup: Save PCS83 project file, record sensor type and scaling for spare replacement.

Warning: This is intrinsically safe equipment for Zone 0. Only certified IS cable and installation rules can be followed; wrong wiring or non-approved accessories will invalidate the ATEX certificate and create explosion risk.

 

Related MTL830 Series Models & Accessories (15 pcs)

Model Order Number Description
Matching receiver Safe area Modbus receiver
Digital isolator IS highway isolator between hazardous & safe side
New generation transmitter MTL831C Successor of (full system replacement)
New generation receiver MTL838C Matching receiver for MTL831C
New isolator MTL5553 Isolator for MTL831C system
Enclosure ENC8 Standard IP67 enclosure for
Large enclosure ENC83 Larger IP67 enclosure
Receiver enclosure ENC83SS Safe-side enclosure for
Configuration software PCS83 Software for MTL830 series setup
Highway twisted pair cable MTL-IS-CABLE IS twisted pair highway cable
Terminal spare kit -TERM Spare terminal block set
Surge protector MTL7787+ Temperature signal surge barrier
MTL830 manual MTL830-MAN System installation manual
Modbus cable MTL-MODBUS-CAB RS485 cable for
MTL4041 MTL4041 RTD isolator (standalone single channel)