Description
IS220PPROH1A, GE Mark VIe PPRO Independent Backup Turbine Protection I/O Pack (Backup Overspeed & E-Stop Protection)
Core Product Introduction
The IS220PPROH1A (PPRO pack) is a safety-critical independent backup protection I/O pack for GE Vernova Mark VIe Speedtronic turbine control system. It provides hardware-based backup overspeed protection, emergency stop (E-Stop) monitoring, control watchdog, generator synchronization check and trip relay outputs, working independently from the main controller protection logic. It receives speed signals from magnetic pickups and emergency trip contact signals, drives turbine trip hardware via TREA / TREG trip terminal boards. Widely used on gas turbines, steam turbines, combined cycle and compressor packages; supports simplex and TMR safety architectures, supplied mainly as spare part for existing Mark VIe fleets.

IS220PPROH1A
Main Technical Specifications
| Item | Parameter |
|---|---|
| Part Number | IS220PPROH1A |
| Manufacturer | GE Vernova (GE Gas Power) |
| Platform | Mark VIe Speedtronic |
| Function | Backup overspeed, E-Stop, watchdog, sync check, turbine trip output |
| Speed Inputs | 3 independent speed pickup channels |
| Communication | Dual 10/100 Mbps IONet Ethernet |
| Termination Mate | TREA / TREG trip terminal board |
| Safety Function | Hardware overspeed trip, wire-break detection for E-stop loops |
| Supply Voltage | 24 VDC from Mark VIe backplane |
| Hot Swap | Supported |
| Operating Temperature | -30 °C ~ +65 °C |
| Storage Temperature | -40 °C ~ +85 °C |
| Humidity | 5%–95% RH, non-condensing |
| Mounting | Mark VIe I/O pack backplane slot mount |
| Weight | ~0.38 kg |
| Certifications | cULus, CE, suitable for TMR turbine protection |
| Lifecycle Status | Obsolete, spare stock available |
Quality Control Procedure
- Visual & Label Inspection: Verify original GE marking, IS220PPROH1A serial number, dual Ethernet ports, gold edge fingers; no pin damage, burn marks or PCB corrosion.
- Backplane Power Boot Test: Install on Mark VIe test backplane, apply 24VDC, confirm PWR, RUN, ESTP, OSPD, WDOG LED status, no abnormal heating.
- IONet Communication Test: Establish IONet connection, confirm ToolboxST can read module identity, revision and fault status.
- Speed Channel Simulation Test: Inject frequency signal to 3 speed inputs, verify overspeed threshold detection.
- E-Stop Loop & Wire-break Test: Simulate E-stop contact open/short circuit, validate wire-break diagnostic alarm.
- Trip Relay Output Test: Check Form-C trip relay action under overspeed and E-stop conditions.
- Watchdog function test: Simulate main controller loss, verify watchdog trip action.
- TREA terminal compatibility check: Confirm cable pinout matching with TREA trip board.
- Firmware Compatibility Check: Confirm firmware matches site ControlST / ToolboxST baseline.
- Packaging & Traceability: Anti-static packaging, foam protection, serial-number QC report before shipment.
Frequently Asked Questions (FAQ)
Q1: What is the difference between PPRO (IS220PPROH1A) and the main controller overspeed protection?A1: PPRO is independent hardware backup protection. It runs separate overspeed logic, not dependent on the main Mark VIe CPU; it provides the second layer of overspeed and emergency trip for turbine safety.
Q2: What terminal board does IS220PPROH1A pair with?A2: It connects to TREA / TREG trip termination boards via 37-pin DC cable.
Q3: Can it be hot swapped online?A3: Hot-swap hardware supported, but protection function is lost during replacement. MOC, trip bypass and alarm suppression are mandatory before swap.
Q4: Is it SIL rated?A4: It is used in turbine TMR protection architectures, but it is a dedicated backup overspeed pack, different from SIL-certified YVIB vibration safety packs. Confirm site safety requirement before substitution.
Q5: Can it work with legacy Mark VI (non-Vie)?A5: No, exclusive to Mark VIe IONet architecture; Mark VI uses separate overspeed hardware.
Q6: What does OSPD, ESTP, WDOG LED stand for?A6: OSPD = Overspeed trip status; ESTP = Emergency Stop active; WDOG = Controller watchdog fault.
Installation & Configuration Guide
- Pre-install Preparation: Mark VIe backplane, TREA trip terminal board, speed probe cables, E-stop wiring, 24VDC rack power, ToolboxST software, site MOC & trip bypass procedure.
- Rack Preparation: Bypass turbine trip protection and suppress related alarms per plant safety procedure.
- Module Insertion: Insert into designated PPRO slot and lock.
- Field Wiring: Connect speed pickups and E-stop chains to TREA terminals; route low-level speed cables separately from high-power cables.
- Power Up: Energize rack power, check RUN, LINK LEDs normal, no active trip alarms.
- Online Connection: Connect ToolboxST to Mark VIe controller and go online.
- Hardware Scan: Run chassis scan, confirm PPRO pack is detected without hardware fault.
- Protection Parameter Configuration: Set overspeed trip threshold, E-stop wire-break detection, watchdog timeout.
- Function Validation: Test speed reading, E-stop trigger, watchdog trip and relay output action.
- Backup: Save ControlST database, PPRO firmware and trip settings to plant archive.
Warning: This pack is part of turbine overspeed & emergency trip protection. Improper replacement or bypass may result in unplanned turbine trip or loss of safety protection.
Related Mark VIe Models & Accessories (15 pcs)
| Model | Order Number | Description |
|---|---|---|
| PPRO Trip Terminal Board | IS200TREAH2A | TREA termination board for PPRO |
| Mark VIe Main Controller | IS220UCSAH1A | Mark VIe CPU |
| IONet Ethernet Switch | IS420ESWBH2A | Mark VIe IONet switch |
| Safety Vibration Pack | IS220YVIBS1A | SIL vibration protection pack |
| Non-safety Vibration Pack | IS220PVIBH1A | PVIB vibration monitor |
| Rack Power Supply | IS200PSAH1A | Mark VIe 24VDC power |
| Speed Probe | 330104-00-05-10-02-00 | Eddy current speed pickup |
| Speed Probe Extension Cable | 330730-080-00-00 | Probe extension cable |
| IONet Patch Cable | GE-CAB-IONET | IONet Ethernet cable |
| PPRO 37-pin Trip Cable | GE-CAB-PPRO-TREA | PPRO to TREA cable |
| Mark VIe Backplane | IS200CHS02A | I/O rack backplane |
| Analog Input Pack | IS210AEAAH1B | 4-20mA AI pack |
| Digital Input Pack | IS210AEDAH1B | DI I/O pack |
| Digital Output Pack | IS210AEDBH1B | DO I/O pack |
| ToolboxST Software | TOOLBOXST-LIC | Mark VIe configuration & diagnostic software |


