Description
GE IS200AEPAH1A AEPA Pitch Axis Control Board, Mark VIe Wind Turbine Automation Spare Part
Product Overview
The GE IS200AEPAH1A (AEPA, Alternative Energy Pitch Axis) is a pitch control I/O board for GE Speedtronic Mark VIe wind turbine control system, mainly used for 1.5MW series wind turbine pitch control system. It is installed inside the hub axis box, working together with BPPB main processor board to collect pitch feedback signals and output drive commands for pitch actuators. This original imported legacy spare is widely stocked for wind farm overhaul and emergency replacement of pitch control loops.

IS200AEPAH1A
Key Technical Specifications
- Part Number: IS200AEPAH1A
- Brand: GE / GE Vernova
- Series: Speedtronic Mark VIe (Wind version)
- Module Type: AEPA Pitch Axis I/O Control Board
- Compatible Unit: 1.5MW GE wind turbine pitch control system
- Matching Main Board: BPPB
- Interface: Backplane internal bus, encoder feedback, analog & digital I/O, relay outputs
- Power Supply: 24 VDC
- Operating Temperature: -20 °C ~ +60 °C
- Storage Temperature: -40 °C ~ +85 °C
- Relative Humidity: 5% ~ 95 %, non-condensing
- Mounting: Installed in hub axis control box
- Hot Swap: Not hot-swappable; power cut required
- Weight: Approx. 0.4 kg
- Coating: Optional conformal coating for offshore salty environment
- Status Indication: Multiple LED for power, communication, fault and axis status
Main Features
- Dedicated pitch axis I/O board for GE Mark VIe 1.5MW wind turbine
- Collects pitch encoder position, speed and limit switch feedback signals
- Outputs control signals to pitch servo drivers and hydraulic pitch actuators
- Interlocks for pitch over-speed, over-angle, emergency feathering protection
- Bidirectional high-speed communication with BPPB main processor board
- Built-in channel fault diagnosis, easy fault location for pitch failure
- Supports redundant pitch channel architecture
- Rugged anti-vibration design to adapt to hub rotating environment
- Configured and diagnosed via GE Mark VIe wind control software
- Scarce end-of-life spare for old GE wind farm maintenance
Product Application Information
IS200AEPAH1A receives pitch angle setpoints from the BPPB main board, collects real-time blade position feedback from encoders, and executes closed-loop pitch regulation to adjust blade angle for power optimization and load limitation. It also triggers emergency feathering when fault conditions occur. If this board fails, the corresponding pitch axis will lose control, the turbine will report pitch fault and trigger shutdown. Wind farms keep this spare on hand to reduce turbine downtime and power loss.
Application Scenarios
- Onshore 1.5MW GE Mark VIe wind turbine pitch control
- Offshore wind farm legacy GE turbine hub control cabinet
- Wind turbine pitch servo / hydraulic actuator control interface
- Wind farm scheduled overhaul spare replacement
- Retrofit project for aging GE wind turbine control system
- Wind power skid pitch safety interlock control
- Distributed wind farm remote pitch fault recovery
- Wind turbine condition-based maintenance spare pool
- Brownfield Mark VIe wind control system upgrade backup
- Wind turbine safety shutdown & feathering loop
Matching / Supporting Components
- IS200BPPBH1B (BPPB) main processor board
- Pitch servo drive or hydraulic pitch valve module
- Pitch position encoder, proximity limit switches
- 24 VDC hub redundant power supply
- Shielded encoder feedback cable
- Mark VIe wind turbine configuration software
- Hub control box cooling and vibration damping assembly
- Emergency feather battery pack
- Pitch cabinet terminal blocks and signal connectors
- Related AEPA variant: IS200AEPAH1ABB
Related 12 Model References
- IS200BPPBH1B
- IS200AEPAH1ABB
- IS200AEADH1A
- IS200VSPAH1AAA
- IS215WEPAH2BB
- IS200ERIOH1A
- IS200TSVOH1A
- IS200UCSAH1A
- IS200WROBH1A
- IS200BPIBH1A
- IS200DSPXH1D
- IS200CRXMG1A


