Bently Nevada 3500/40M Proximitor Monitor Module, Industrial Automation Spare Part

  1. 3500/22M TDI
  2. 3500/15 Power Supply
  3. 3500/42M Proximitor / Seismic Monitor
  4. 3500/45M Temperature Monitor
  5. 3500/50M Tachometer Module
  6. 3500/53M Relay Module
  7. 3500/60M Overspeed Module
  8. 3500/62M Overspeed Module
  9. 330104 Proximity Probe
  10. 330780 Extension Cable
  11. 330130 Proximitor
  12. 3500/92 Gateway
  13. 3500/94 Display
  14. 3500/05 System Rack
  15. 130740-01 Probe Cable
Category: SKU: Bently 3500/40M Brand:

Description

Bently Nevada 3500/40M Proximitor Monitor Module, Industrial Automation Spare Part

3500/40M

Main Technical Specifications

 

Item Specification
Brand Bently Nevada (Baker Hughes)
Model 3500/40M
Common Part Nos. 125680-01, 176449-01, 126615-01
Series 3500 Machinery Protection System
Product Type 4‑Channel Proximitor Displacement Monitor
Input Sensor Eddy current proximity probe (3300 series)
Measurement Functions Radial vibration, thrust position, differential expansion, eccentricity, REBAM®
Channel Arrangement Configured in pairs (Ch1+Ch2, Ch3+Ch4)
Power Consumption Typical 7.7 W
Frequency Response 0.5 Hz ~ 20 kHz
Operating Temperature -30 ℃ ~ +65 ℃
Ambient Humidity 5%–90% RH, non-condensing
Protection Rating IP20, for rack cabinet installation
Mounting Standard slot of 3500 rack backplane
Diagnostic Channel, OK, Fault status LEDs
Certification ATEX / IECEx Zone 2, UL, CSA, SIL 2 capable in qualified configuration
Application Turbine, compressor, large pump and fan shaft displacement & vibration protection

 

Quality Control Procedure

  1. Visual Incoming Inspection: Check front panel BNC probe connectors, rack edge connector, label, serial number and PCB condition.
  2. ESD Controlled Handling: All inspection and testing performed on grounded anti-static workstation with ESD wrist strap.
  3. Power-on Burn-in Test: Install into compatible 3500 rack, energise continuously for 4 hours; monitor LED status and temperature.
  4. Backplane Communication Test: Verify handshake and cyclic data exchange with 3500/22M TDI.
  5. Probe Signal Calibration Test: Inject proximity simulator signal for each channel, verify linearity and measurement accuracy.
  6. Alarm Setpoint Test: Confirm Alert / Danger alarm trigger and trip logic response.
  7. Firmware Compatibility Check: Confirm firmware revision matches the existing rack configuration.
  8. Data Archiving: Record serial number and full test report, attach inspection sticker, vacuum anti-static packaging.
  9. Pre-shipment Audit: Double-check model and terminal variant (internal / external terminals) before dispatch.

 

Recommended Related Models & Order Codes (15pcs)

  1. 3500/22M TDI
  2. 3500/15 Power Supply
  3. 3500/42M Proximitor / Seismic Monitor
  4. 3500/45M Temperature Monitor
  5. 3500/50M Tachometer Module
  6. 3500/53M Relay Module
  7. 3500/60M Overspeed Module
  8. 3500/62M Overspeed Module
  9. 330104 Proximity Probe
  10. 330780 Extension Cable
  11. 330130 Proximitor
  12. 3500/92 Gateway
  13. 3500/94 Display
  14. 3500/05 System Rack
  15. 130740-01 Probe Cable

 

Frequently Asked Questions

Q1: Can 3500/40M replace 3500/42M directly?A: No. 3500/40M only supports eddy current proximity probe displacement measurement; 3500/42M accepts both proximity and seismic velocity/acceleration sensors. Confirm sensor type, rack configuration and alarm logic before replacement.

Q2: Is this module discontinued?A: Yes, Bently Nevada 3500/40M is end-of-production. Available stock is original surplus or fully tested refurbished spare parts.

Q3: Does 3500/40M support hot swap?A: Hardware supports hot swap, but this module is inside the machine protection trip path. The related shaft vibration / thrust protection will be lost during replacement. Mandatory risk assessment, bypass and plant permit are required before any hot swap.

Q4: Channel fault alarm after installation, what should I check?A: Check probe, extension cable, Proximitor, BNC connection, gap voltage, channel configuration, alarm setpoints and rack firmware. Use 3500 configuration software to read channel diagnostics.

Q5: Warranty terms?A: Original surplus new: 12-month warranty. Refurbished tested stock: 6-month warranty. Damage caused by probe short circuit, overvoltage, ESD, wrong gap calibration or incompatible firmware is excluded.

Q6: Commissioning software?A: Bently Nevada 3500 Rack Configuration Software and System 1. Back up the full rack configuration, channel scaling and alarm setpoints before replacement.

 

Installation & Configuration Guide

Pre-installation Preparation

  • Confirm cabinet environment: clean, low dust, no condensation, separated from high EMI and high-voltage cabling.
  • Prepare ESD protection, insulated screwdriver, proximity probe simulator, BNC cables and rack project backup.
  • Complete safety permit, protection bypass and trip prevention procedure for rotating equipment.

Installation Steps

  1. Follow site LOTO and rotating equipment safety procedure, implement protection bypass.
  2. Release the module latch, pull out the faulty 3500/40M vertically from the rack slot.
  3. Unpack new spare under ESD protection; avoid touching backplane gold fingers and BNC internal pins.
  4. Insert the new module smoothly into the rack slot and lock the latch.
  5. Reconnect BNC probe cables; check probe gap voltage and wiring shielding.
  6. Verify rack protective earth connection.

Configuration & Commissioning

  1. Observe front panel LED status after insertion.
  2. Launch 3500 configuration software and connect to the rack via TDI.
  3. Refresh hardware tree, confirm 3500/40M is recognised online.
  4. Load saved configuration, verify channel pairing, measurement type, scaling, Alert and Danger setpoints.
  5. Use signal simulator to calibrate each channel, confirm gap and displacement reading correct.
  6. Test alarm and trip output function, clear all rack alarms after self-diagnosis passes.
  7. Remove bypass step by step, restore machinery protection logic and save commissioning log.

Maintenance Notes

  • This module is critical for machine protection; never bypass protection without plant approval.
  • Keep BNC connectors clean; dirt or loose connection causes intermittent channel faults.
  • Regularly check probe gap voltage and cable insulation.
  • Store spare modules in dry sealed anti-static packaging.