Allen‑Bradley 1394C‑SJT10‑A | Bulletin 1394 SERCOS Multi-Axis Servo System Module

  1. 1394C-SJT10-T – 10kW system module with HIM interface
  2. 1394C-SJT05-A – 5kW SERCOS system module, no HIM
  3. 1394C-SJT05-T – 5kW SERCOS system module with HIM
  4. 1394C-AM03 – Analog servo axis module
  5. 1394C-AM07 – 7A analog axis module
  6. 1394C-AM15 – 15A analog axis module
  7. 1394C-AM30 – 30A analog servo axis
  8. 1394C-SRM05 – SERCOS regulator module
  9. 1394C-SRM10 – 10kW SERCOS regulator
  10. 1394C-IF03 – SERCOS fiber interface module
  11. 1394C-PM06 – Power supply module
  12. 1394C-PM10 – 10kW power module
  13. 1394C-ENET – Ethernet communication adapter for 1394
  14. 1394C-BUS1 – DC bus distribution module
  15. 1394C-FDB1 – Feedback interface board

 

Category: SKU: Allen 1394C SJT10 Brand:

Description

Allen‑Bradley 1394C‑SJT10‑A | Bulletin 1394 SERCOS Multi-Axis Servo System Module

 

Product Description

1394C‑SJT10‑A is a discontinued Rockwell Allen‑Bradley Bulletin 1394 Series C SERCOS servo system module, designed as a main power & motion controller for multi-axis digital servo systems. It operates as a SERCOS interface master unit to coordinate synchronized motion across multiple servo axes, equipped with built-in analog ±10V command interface, without HIM human interface module. Rated 10kW continuous power, 3‑phase 360–480VAC input, peak output current 15A. This unit integrates DC bus power supply, motion profile generation, electronic CAM, position/velocity/torque closed-loop control and full servo fault protection. Widely deployed on high-speed synchronized machinery. End-of-life by Rockwell since 2012; available as surplus, refurbished spare part for legacy machine maintenance.

1394C-SJT10-A

Technical Specifications

 

Item Parameter
Part Number 1394C-SJT10-A
Manufacturer Allen‑Bradley (Rockwell Automation)
Product Line Bulletin 1394 Series C Servo System Module
Communication SERCOS fiber optic interface; ±10V analog command
Input Power 3‑Phase 360–480 VAC, 50/60Hz
Continuous Output Power 10kW @ 480VAC
Peak Output Current 15 A
DC Bus Voltage 530–680 VDC
Feature No HIM keypad, with analog interface, electronic CAM
Electronic CAM Profiles Up to 13,000 master/slave cam points
Overload Protection Overvoltage, undervoltage, overcurrent, overtemperature, short-circuit
Operating Temperature 0℃ ~ +50℃
Storage Temperature -20℃ ~ +70℃
Mounting Cabinet panel mount
Dimension 350 × 280 × 150 mm
Weight ~4.94 kg
Status Discontinued (EOL 2012)

 

Compatibility & Installation Pitfalls

Compatibility

  • System Platform: Allen‑Bradley Bulletin 1394 SERCOS multi-axis servo rack
  • SERCOS Axes: Matched 1394 series servo axis modules, fiber SERCOS ring topology
  • Servo Motors: AB 1326 / 1392 series brushless servo motors
  • Programming Software: Motion Explorer / Motion Planner for 1394 series
  • Module Variant Note: SJT = System module; do not mix with SJTxx-T variants with HIM

Critical Installation Pitfalls

  1. SERCOS fiber ring wiring error: SERCOS uses ring topology; broken fiber or wrong TX/RX cross connection will crash entire motion network. Must follow IN/OUT fiber sequence strictly.
  2. DC bus pre-charge risk: High voltage DC bus inside module. LOTO procedure mandatory before opening cover; residual capacitance can hold lethal voltage for minutes after power off.
  3. Cooling airflow requirement: Side ventilation gaps must be kept clear. Dust accumulation or blocked cooling fan triggers over-temperature trip during high-duty cycle motion.
  4. Grounding & EMI: Power cable and SERCOS fiber must be separated; motor power shield single-point grounding. Poor grounding causes position jitter and false overcurrent alarms.
  5. Firmware revision lock: SERCOS ring firmware must be consistent across all 1394 modules. Mismatched firmware causes synchronization failure or axis runaway risk.
  6. No hot swap: Never remove or insert module while main 3-phase AC power energized. Hot-plug damages power stage and SERCOS transceiver.
  7. Analog wiring noise: ±10V analog command cable must use shielded twisted pair; avoid running alongside high-current motor cables.
  8. Spare replacement caveat: EOL part. Refurbished units require full load test and firmware validation before machine production.

 

Standard Operating Procedure (SOP)

1. Pre-Installation & LOTO

  • Verify part number 1394C-SJT10-A, inspect cabinet housing, terminal blocks, fiber ports for burn marks or physical damage.
  • Execute Lockout/Tagout of 3-phase mains; wait minimum 5 minutes for DC bus capacitors to fully discharge, confirm zero voltage measurement.
  • Prepare SERCOS optical fiber cables, shielded analog cables, ESD protection, Motion Explorer software, project backup.

2. Mechanical Mounting

  • Mount module on cabinet backplate with specified mounting torque. Maintain minimum clearance on top and bottom for convection cooling.
  • Secure earth protective ground wire to cabinet ground bus.

3. Wiring & SERCOS Setup

  • Wire 3-phase AC input, DC bus, analog ±10V command, enable and fault signal wiring according to machine schematic.
  • Install SERCOS fiber ring, follow TX → IN, OUT → next axis IN sequence to complete closed fiber ring.
  • Terminate motor and analog cable shields properly. Double check power polarity and terminal tightness.

4. Power-Up & Commissioning

  • Restore AC power, observe front panel LED status: Power, SERCOS Link, Fault.
  • Connect Motion Explorer, upload or download motion project, verify firmware version consistency across SERCOS ring.
  • Configure electronic CAM, position/velocity/ torque loop parameters, tune servo gains for each axis.
  • Perform single-axis jog test first, then synchronized multi-axis motion test.
  • Test fault interlock, emergency stop, over-travel limit protection functions.
  • Run dry cycle without load, then full production trial run.

5. Maintenance & Replacement

  • Periodically clean cooling filter, check fiber connector cleanliness, terminal tightness and module operating temperature.
  • For replacement: LOTO + capacitor discharge, wear ESD protection, remove faulty unit, install spare module, reload motion project, re-tune servo gains, validate SERCOS ring communication.
  • Retrieve fault codes via Motion Explorer for troubleshooting overcurrent, overheat, SERCOS link dropouts.

 

Application Scenarios

  1. High-speed multi-axis synchronized motion for printing & converting machinery
  2. Packaging automation, carton forming and cut-to-length machines
  3. Metal processing, flying shear and rotary cut applications
  4. Textile spinning and weaving high-precision synchronized lines
  5. Special-purpose machine tools and automated assembly equipment

 

Supporting / Matching Components

  1. Bulletin 1394 SERCOS axis servo modules
  2. Allen‑Bradley 1326 /1392 brushless servo motors
  3. SERCOS optical fiber cables and fiber connectors
  4. Motion Explorer / Motion Planner configuration software
  5. 3-phase mains EMI input filter
  6. Dynamic brake resistors
  7. Emergency stop & safety interlock relay assembly
  8. Shielded twisted pair analog signal cables
  9. Motor power shielded cables
  10. Cabinet cooling fan and air filter

 

15 Recommended Same-Series / Compatible Models (Bulletin 1394)

  1. 1394C-SJT10-T – 10kW system module with HIM interface
  2. 1394C-SJT05-A – 5kW SERCOS system module, no HIM
  3. 1394C-SJT05-T – 5kW SERCOS system module with HIM
  4. 1394C-AM03 – Analog servo axis module
  5. 1394C-AM07 – 7A analog axis module
  6. 1394C-AM15 – 15A analog axis module
  7. 1394C-AM30 – 30A analog servo axis
  8. 1394C-SRM05 – SERCOS regulator module
  9. 1394C-SRM10 – 10kW SERCOS regulator
  10. 1394C-IF03 – SERCOS fiber interface module
  11. 1394C-PM06 – Power supply module
  12. 1394C-PM10 – 10kW power module
  13. 1394C-ENET – Ethernet communication adapter for 1394
  14. 1394C-BUS1 – DC bus distribution module
  15. 1394C-FDB1 – Feedback interface board

 

FAQ

  • Q: Is 1394C-SJT10-A still manufactured by Rockwell? A: No, discontinued since 2012. Only surplus / refurbished spare units available for legacy machine maintenance.
  • Q: Can I replace 1394C–A directly with 1394C–T? A: Hardware power stage compatible, but -T includes HIM port. You need to adjust project configuration; not fully drop-in without parameter check.
  • Q: Can SERCOS ring run with broken fiber? A: SERCOS ring will stop motion if fiber cut or TX/RX reversed. The ring topology requires all fiber links intact.
  • Q: Is it safe to touch terminals after power off? A: No. DC bus capacitors retain high hazardous voltage for several minutes after power cut; mandatory discharge verification.