Description
ABB ACU-01B 3HNA024871-001 Robot Spray Process Control Unit
Product Core Introduction
3HNA024871-001 (official designation ACU-01B) is ABB’s high-performance sealed spray process control unit, purpose-built for ABB industrial painting robot systems. As the core execution hardware dedicated for paint flow regulation, pressure closed-loop control and nozzle parameter management, it is natively optimized for ABB IRC5 robot controller platform, delivering micron-level precision for automotive body painting, industrial coating and surface treatment applications. Its fully sealed rugged enclosure design provides full protection against paint mist, solvent vapor, dust and high humidity in harsh painting workshop environments, ensuring long-cycle uninterrupted operation over 8000 running hours per year.

ACU-01B 3HNA024871-001
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Full Part Number | ABB 3HNA024871-001 (ACU-01B) |
| Manufacturer | ABB Robotics, Sweden |
| Core Function | Paint flow regulation, spray pressure closed-loop control, nozzle parameter management |
| Supported Robot Models | IRB 5400, IRB 580, IRB 5500, IRB 52 painting robot series |
| Host Controller Compatibility | Native seamless integration with ABB IRC5 robot controller platform |
| Communication Protocols | CAN 2.0B, RS-485, 10/100Mbps Ethernet |
| I/O Configuration | 4-8 configurable digital/analog output channels for spray actuator driving |
| Protection Rating | IP65 fully sealed enclosure, resistant to paint mist, solvent vapor and water splash |
| Operating Temperature Range | 0°C to +55°C |
| Power Supply | 24 VDC industrial input, 15W maximum power consumption |
| Installation Method | Direct mounting on robot arm or painting process cabinet |
| Standard Warranty | 12 months from delivery |
| Supply Status | Active production, available via ABB official authorized distributors |
6 Recommended Compatible Models in the Same Series
- 3HNA024871-002: ACU-01B standard variant with basic 4-channel analog output, for general small-component painting robot applications
- 3HNA024871-003: Extended 8-channel high-density version, supporting simultaneous control of 8 independent spray valves for multi-color complex painting processes
- ACU-02B: Next-generation upgraded spray control unit, with built-in predictive maintenance function and EtherNet/IP PROFINET dual protocol support
- 3HNA015147-001: ABB IRC5 robot main drive board, paired with ACU-01B to complete full robot motion + spray process integrated control
- 3HNA023098-001: Paint flow sensor interface module, directly connected to ACU-01B for real-time paint consumption metering and closed-loop feedback
- 3HNA025074-001: Explosion-proof intrinsically safe variant, certified for Class I Division 1 hazardous painting zone applications with flammable solvent vapor environment
Professional Quality Control Test Standard Operating Procedure
- Visual & Mechanical Pre-Inspection
Verify IP65 enclosure sealing integrity, connector alignment and mounting bracket condition; confirm no physical damage on PCB components and sealing gasket. - I/O Precision Calibration Bench Test
Inject NIST-traceable standard reference signals, verify all analog output channels full-scale accuracy deviation stays within ±0.1% tolerance. - Communication Stability Validation
Connect to real IRC5 controller, run 72-hour continuous data transmission test, ensure zero CAN bus frame loss and 100% data integrity. - Solvent Vapor Endurance Test
Place unit in environmental chamber with simulated painting workshop xylene solvent vapor atmosphere for 48 hours, confirm no material corrosion or function degradation after test. - IP65 Water & Dust Ingress Test
Perform standardized IP65 test per IEC 60529 standard, confirm no water or dust penetrates into internal PCB compartment. - Final Firmware Calibration & Release
Upgrade to latest official ABB robot compatible firmware, run full diagnostic scan, write unique serial number into non-volatile memory, attach qualified product label and release for shipment.
New Module Installation & Startup Guideline
- Power off the IRC5 robot controller main power supply, perform full ESD protection preparation before removing the old module.
- Mount the new unit on robot arm or process cabinet with original mounting screws, confirm all sealing gaskets are correctly seated to maintain IP65 protection rating.
- Connect CAN bus, 24VDC power supply and spray actuator cables strictly following ABB official wiring diagram, confirm all cable glands are tightened to maintain enclosure sealing performance.
- Power on the IRC5 controller, run RobotStudio software to automatically identify the new module, import pre-backed-up spray process parameter configuration.
- Perform offline spray simulation test without paint, verify all flow, pressure and nozzle control signals respond correctly; run 30-minute no-load stability monitoring before restoring normal painting production operation.
Application Scenarios & Distinctive Features
- Automotive Body Painting Lines: Delivers ultra-precise paint flow and atomizing air pressure control for automotive topcoat painting, drastically reducing paint waste and improving finished body surface finish quality.
- Industrial Component Anti-Corrosion Coating Lines: Serves as core process control unit for heavy equipment, engineering machinery and metal component painting, ensuring uniform coating thickness and meeting anti-corrosion 10-year service life requirement.
- Hazardous Explosion-Proof Painting Zones: Fully sealed intrinsically safe design eliminates electrical spark risk, fully compliant with ATEX explosion-proof standard for flammable solvent vapor environment.
- Legacy ABB Painting Robot System Renovation Projects: Direct drop-in replacement for aged ACU series modules, no modification required to existing robot wiring or original painting process program.
- Core Advantages: IP65 fully sealed anti-corrosion design, native platform seamless compatibility, sub-10ms spray parameter response, zero drift long-term operation in harsh painting workshop environment.

ACU-01B 3HNA024871-001
Frequently Asked Questions
- Q: The module cannot be recognized by controller after installation?
A: Confirm the CAN bus baud rate setting matches controller configuration, verify module firmware version is compatible with current RobotWare system version. - Q: The spray flow shows obvious fluctuation during production?
A: Check if paint flow sensor feedback cable shielding layer is properly grounded, re-calibrate flow closed-loop PID parameters in RobotStudio spray configuration menu. - Q: Can I use this module on non-ABB third-party painting robots?
A: No, is natively optimized for ABB platform, it cannot be directly integrated with other brand robot control systems without dedicated protocol conversion. - Q: What is the maximum allowable operating temperature of this module?
A: Rated operating temperature range is 0-55°C; ensure painting workshop ventilation and cooling system is functioning properly, operating above 55°C will drastically shorten module service life. - Q: What is the core difference between and ordinary general-purpose PLC I/O modules?
A: has dedicated painting process control logic preloaded, anti-solvent sealed design, and sub-10ms ultra-fast response that general PLC modules cannot achieve for high-precision spray control scenarios.


