5105-DFCM-PDPS ProSoft DF1 to PROFIBUS DP Slave Gateway: Full Technical Introduction

  • Allen-Bradley PLC-5 Legacy Serial Controllers
  • Allen-Bradley SLC 500 Series PLCs
  • Allen-Bradley MicroLogix 1100/1400 DF1-enabled Controllers
  • Siemens S7-300 PROFIBUS DP Master PLCs
  • Siemens ET 200M PROFIBUS Distributed I/O Systems
  • ProSoft Configuration Builder Software
  • PROFIBUS DP Standard Field Cables (9.6 kbps to 12 Mbps rated)
  • 24V DC Industrial DIN Rail Power Supplies

 

Category: SKU: 5105-DFCM-PDPS DF1 Brand:

Description

5105-DFCM-PDPS ProSoft DF1 to PROFIBUS DP Slave Gateway: Full Technical Introduction

The ‌5105-DFCM-PDPS‌ is a high-performance industrial protocol gateway purpose-built by ProSoft Technology, engineered to deliver seamless bidirectional translation between Allen-Bradley DF1 serial protocol and PROFIBUS DP Slave networks. As a dedicated protocol bridge, it eliminates the need for custom PLC programming or expensive third-party controller upgrades, enabling native interoperability between legacy Rockwell automation equipment and PROFIBUS-based distributed I/O systems across global industrial deployments.

5105-DFCM-PDPS

Core Product Information

Parameter Detailed Specification
‌Official Part Number‌ 5105-DFCM-PDPS
‌Manufacturer‌ ProSoft Technology (Emerson Automation Solutions)
‌Device Type‌ DF1 Master/Slave to PROFIBUS DP Slave Industrial Protocol Gateway
‌List Price‌ ¥6666 CNY / ~$980 USD for new original units
‌Mounting Form Factor‌ Standard DIN rail mount, compact industrial enclosure
‌Supported DF1 Modes‌ DF1 Full-Duplex Master, DF1 Half-Duplex Master, DF1 Slave
‌PROFIBUS DP Compliance‌ Fully certified PROFIBUS DP V0/V1 Slave, up to 12 Mbps baud rate
‌Configuration Interface‌ DB-9M RS-232 serial port (no hardware handshaking required)
‌Warranty‌ 1-year original factory standard warranty
‌Typical Use Cases‌ Legacy Allen-Bradley PLC retrofitting, PROFIBUS system integration, cross-brand industrial network bridging, factory automation protocol migration

 

Key Technical Specifications

Power & Electrical Characteristics

  • ‌Nominal Power Supply‌: 24V DC, with wide input tolerance from 18V DC to 32V DC for unstable industrial power environments
  • ‌Maximum Current Draw‌: 500mA @ 32V DC, total power consumption under 16W for low-heat cabinet operation
  • ‌Terminal Design‌: Screw-type power terminals compatible with 2.5mm flat screwdrivers, supporting secure field wiring
  • ‌Isolation Rating‌: Full galvanic isolation between DF1 serial port, PROFIBUS DP interface, and power supply, eliminating ground loop noise and common-mode signal interference

Environmental & Physical Ratings

  • ‌Operating Temperature Range‌: -20°C to +50°C (-4°F to 122°F), rated for unconditioned industrial control cabinet deployment
  • ‌Storage Temperature Range‌: -40°C to +85°C (-40°F to 185°F) for long-term spare part storage
  • ‌Humidity Tolerance‌: 5% to 95% non-condensing, compliant with global industrial environmental standards
  • ‌Standard Dimensions‌: 132mm (H) × 52.5mm (W) × 114.8mm (D), ultra-compact footprint for dense DIN rail mounting
  • ‌Extended Variant Dimensions‌: 132mm (H) × 69.3mm (W) × 114.8mm (D), for units with optional expanded I/O capacity
  • ‌Ingress Protection‌: IP20 rated, designed exclusively for installation inside sealed industrial control cabinets

Communication Performance

  • ‌DF1 Serial Interface‌: Supports RS-232/RS-422/RS-485 physical layers, with baud rates configurable from 110 bps up to 115.2 kbps
  • ‌PROFIBUS DP Interface‌: Auto-baud rate detection from 9.6 kbps to 12 Mbps, supporting up to 244 bytes of bidirectional cyclic I/O data exchange
  • ‌Data Mapping Flexibility‌: Fully configurable tag mapping between DF1 register addresses and PROFIBUS process data objects, no fixed memory offset limitations
  • ‌Real-Time Performance‌: End-to-end protocol translation latency <10ms, ensuring deterministic data synchronization for high-speed process control loops
  • ‌Diagnostic LEDs‌: Dedicated status indicators for power, module health, application runtime, serial port activity, and serial error conditions, enabling instant on-site fault identification

 

Core Functional Advantages

  1. ‌Native Bidirectional Protocol Translation‌: The gateway performs full DF1 to PROFIBUS DP Slave protocol conversion at the hardware level, eliminating the need for custom PLC ladder logic programming that would consume valuable controller scan time.
  2. ‌Dual DF1 Operating Modes‌: It can be configured as either DF1 Master or DF1 Slave, making it compatible with the full range of legacy Allen-Bradley PLC-5, SLC 500, and MicroLogix controllers that use DF1 serial communication.
  3. ‌Zero Controller Firmware Upgrade Requirement‌: The unit acts as a transparent protocol bridge, allowing older Rockwell controllers with no native PROFIBUS support to seamlessly integrate with modern PROFIBUS DP distributed I/O systems without hardware modifications.
  4. ‌Robust Industrial Environmental Design‌: The wide -20°C to +50°C operating temperature range and full electrical isolation make it suitable for deployment in harsh industrial environments with extreme temperature swings and high electromagnetic interference.
  5. ‌Simplified Commissioning Workflow‌: The dedicated RS-232 configuration port and ProSoft free configuration software enable fast setup of data maps, baud rates, and station addresses, cutting typical integration time by over 70% compared to custom software-based protocol conversion solutions.
  6. ‌Comprehensive Built-In Diagnostics‌: The multi-color status LED array provides instant visual feedback for power faults, communication timeouts, and configuration errors, drastically reducing mean time to repair (MTTR) during unplanned network outages.

 

Recommended Compatible Industrial Models

  • Allen-Bradley PLC-5 Legacy Serial Controllers
  • Allen-Bradley SLC 500 Series PLCs
  • Allen-Bradley MicroLogix 1100/1400 DF1-enabled Controllers
  • Siemens S7-300 PROFIBUS DP Master PLCs
  • Siemens ET 200M PROFIBUS Distributed I/O Systems
  • ProSoft Configuration Builder Software
  • PROFIBUS DP Standard Field Cables (9.6 kbps to 12 Mbps rated)
  • 24V DC Industrial DIN Rail Power Supplies

 

Compatibility Notes & Installation Pitfalls

  • ‌DF1 Handshaking Configuration‌: The configuration DB-9 port does not support hardware handshaking; you must disable all RTS/CTS and DTR/DSR handshaking settings in your configuration software to establish a valid connection .
  • ‌PROFIBUS Station Address Assignment‌: The factory default PROFIBUS DP slave address is not pre-configured; you must assign a unique, unused station address (1-125) on your PROFIBUS network before commissioning to avoid communication conflicts.
  • ‌Cable Separation Mandate‌: Never route DF1 serial cables or PROFIBUS DP cables in the same cable tray as high-voltage variable frequency drive power cables, as this will introduce severe electromagnetic noise that causes intermittent communication dropouts.
  • ‌Data Mapping Size Limit‌: The maximum total cyclic I/O data size for bidirectional exchange is 244 bytes; for applications requiring larger data volumes, you must split the data into multiple non-cyclic PROFIBUS read/write operations.
  • ‌Grounding Best Practice‌: The gateway chassis must be connected directly to the control cabinet protective earth ground using a short, heavy-gauge ground wire to suppress electrostatic discharge and common-mode noise.

 

Standard Operating Procedure (SOP) for Deployment

  1. Mount the 5105-DFCM-PDPS unit on a standard DIN rail inside the control cabinet, ensuring minimum 25mm clearance on all sides for natural air convection cooling.
  2. Wire the 24V DC power supply to the dedicated power terminals, connect the DF1 serial port to your Allen-Bradley PLC DF1 communication port, and wire the PROFIBUS DP port to your PROFIBUS master network.
  3. Connect your configuration PC to the unit’s DB-9 RS-232 configuration port, launch ProSoft Configuration Builder software, and establish a direct connection to the gateway.
  4. Configure the DF1 communication parameters (baud rate, parity, stop bits, master/slave mode) to exactly match your connected Allen-Bradley PLC settings, then set the PROFIBUS DP slave address and baud rate to match your PROFIBUS master network configuration.
  5. Define your bidirectional data mapping table, assigning DF1 PLC register addresses to corresponding PROFIBUS DP process data objects, then download the full configuration to the gateway non-volatile memory.
  6. Power cycle the unit, verify all status LEDs show normal operation, confirm bidirectional data exchange is active between the DF1 PLC and PROFIBUS master, and validate that all mapped process values are updating correctly in real time.

 

Typical Industrial Application Scenarios

The 5105-DFCM-PDPS is the industry standard protocol bridge for retrofitting legacy Rockwell automation systems across segments including automotive assembly lines, water treatment plants, food and beverage processing facilities, mining conveyor control systems, and legacy manufacturing line upgrades. It allows plant operators to extend the service life of existing DF1-based PLC systems by decades, avoiding costly full controller replacement projects while enabling seamless integration with modern PROFIBUS distributed I/O and SCADA systems.