Bently Nevada 87199-01 3300 XL NSv Narrow Side-View Eddy Current Proximity Probe, Compact Side-View Probe for Limited Counterbore Machinery Vibration & Position Monitoring
Technical Specifications
- Catalog Number: 87199-01
- Brand: Bently Nevada (Baker Hughes)
- Product Type: NSv (Narrow Side View) eddy current proximity probe
- Series: 3300 XL NSv transducer system
- Probe Body Diameter: 5 mm
- Linear Range: 1.27 mm (50 mils)
- Sensitivity: 7.87 V/mm (200 mV/mil) on 4140 steel target
- Frequency Response: 0 ~ 12 kHz (±3 dB)
- Operating Temperature: -40 °C ~ +177 °C (-40 °F ~ +350 °F)
- Cable: Integrated 50 Ω coaxial cable
- Connector: 2-pin Bently custom connector for extension cable mating
- Target Requirements: Minimum target size for NSv small-shaft application; target material ferromagnetic steel
- Compatibility: Matched with 3300 XL NSv Proximitor and NSv extension cable
- Monitoring Rack Compatibility: 3500 series monitors, 3300 monitors, System 1
- Lifecycle Status: Mature field-proven sensor, spare available
- Compliance: API 670, CE, EMC; Class I Div 2 suitable for hazardous machinery compartments
- Weight: ~0.1 kg
Key Features & Advantages
- Narrow side-view (NSv) geometry: Designed for tight counterbore, limited radial clearance where standard 5 mm / 8 mm probes cannot install; common on centrifugal compressors.
- Small footprint for small shafts: Works reliably on shaft diameters below 51 mm (2 inch) and small flat thrust targets.
- Standard 3300 XL sensitivity: Maintains the industry standard 7.87 V/mm scaling for simple drop-in replacement without monitor rescaling.
- Wide temperature rating: Suitable for hot compressor casings, turbine and process gas machinery.
- Eddy current non-contact measurement: No wear, no friction, stable continuous monitoring of shaft relative vibration, thrust position.
- Multi-function capability: Radial vibration, axial thrust position, Keyphasor / tachometer zero-speed trigger applications.
- Full 3300 XL transducer system architecture: Probe + extension cable + Proximitor sensor as a calibrated matched set.
- API 670 certified: Accepted for safety-critical rotating machinery protection systems.
Application Fields
- Centrifugal process gas, refrigeration and air compressors
- Turbo-expanders and small high-speed rotating machinery
- Steam/gas turbine auxiliary shafts and thrust bearing monitoring
- Pump and gearbox vibration and thrust monitoring with restricted installation space
- Keyphasor phase reference and shaft speed pickup
- Offshore, refinery and LNG rotating equipment condition monitoring
- Retrofit replacement for existing NSv probe installations
- Machinery protection systems requiring small target proximity measurement
Related Product Recommendations
- 84661-xx: NSv extension cable (different lengths)
- 330180-xx: 3300 XL NSv Proximitor sensor
- 3500/42M: 3500 vibration / position monitor module
- 3500/44M: 3500 thrust / position monitor
- 3300/20: Legacy 3300 monitor rack
- Standard 330103 8 mm probe: Standard probe for larger counterbore
- 330104 5 mm standard probe: Straight 5 mm probe (not side-view)
- 990 Vibration Transmitter: Standalone transmitter for NSv probe
- System 1 software: Condition monitoring, trending and alarm management
- Probe mounting adapter, compression fitting and locknut assemblies
Installation & Maintenance
Installation
- Install the NSv probe strictly per side-view counterbore drawing; maintain correct target gap within linear range (typical mid-gap 0.6 mm).
- Use the matching NSv extension cable and NSv Proximitor; standard Proximitor is not calibrated for NSv probes.
- Keep the coaxial cable routing separated from high-current power cables, VFD and relay wiring to reduce noise pickup.
- Secure probe with locknut and anti-vibration fitting; avoid mechanical stress on the probe body and cable root.
- Perform gap setting using DC voltage reading from Proximitor output before lock-down.
- Verify target size and material; insufficient target area or non-ferrous material will degrade linearity and sensitivity.
- For hazardous areas, follow site drawing, IS / Class I Div 2 installation rules and cable separation requirements.
- Record gap voltage, probe serial, cable serial and Proximitor serial as a calibrated transducer set.
Maintenance
- During turnaround inspection, check probe cable insulation, connector integrity and mounting locknut looseness.
- Monitor “Not OK” alarm in 3500 / System 1; intermittent alarms often come from damaged coax, bad connector or cable fatigue.
- Do not interchange NSv and standard 3300 XL probes or Proximitors; calibration curves differ.
- Keep spare complete calibrated NSv sets (probe + cable + Proximitor) for critical compressors.
- After replacement, re-set gap, verify linearity check and confirm vibration/thrust readings match baseline before return to service.
- Preserve transducer calibration certificate and gap log in machinery protection asset records.
- Do not repair or splice the internal coaxial cable in the field; damaged probe requires replacement.
Ready for your next part number? Same template.
今天 10:42
288055-01+146031-01
288055-01 + 146031-01
Title
Bently Nevada 288055-01 Accelerometer + 146031-01 Mounting Base, 330500 Series High-Frequency Piezoelectric Velocity Transducer, Case Vibration Sensor for Turbomachinery
Technical Specifications
- Catalog Number: 288055-01 (Accelerometer Sensor), 146031-01 (Magnetic / Stud Mount Base)
- Brand: Bently Nevada (Baker Hughes)
- Product Type: Piezoelectric accelerometer, 330500 series velocity transducer
- Measurement Type: Case absolute vibration (acceleration / velocity)
- Sensitivity: 100 mV/g nominal
- Frequency Range: 5 Hz ~ 10 kHz (±3 dB)
- Dynamic Range: ±80 g peak
- Resonance Frequency: ≥25 kHz
- Housing Material: 316L stainless steel
- Operating Temperature: -55 °C ~ +121 °C (-67 °F ~ +250 °F)
- Electrical Connector: 2-pin MIL circular connector
- Mounting: Direct stud mount or magnetic base (146031‑01)
- Output: AC coupled, low impedance piezoelectric signal
- Compatibility: 3500/45, 3500/42M monitors, 3300 monitors, System 1
- Lifecycle Status: Mature spare part, supported for legacy TSI systems
- Compliance: API 670, CE, Class I Div 2 hazardous area rating
- Weight (Sensor alone): ~70 g; Assembly with base ~110 g
Key Features & Advantages
- Paired assembly: 288055‑01 vibration sensor mates with 146031‑01 mounting base for quick installation on machine casings.
- High frequency response: Captures bearing fault, gear mesh and blade pass vibration that proximity probes cannot detect.
- 316L stainless steel construction: Resists corrosion in refinery, offshore, humid and corrosive process environments.
- Low impedance output: Good noise immunity for moderate cable lengths in machinery compartments.
- Dual mounting option: 146031‑01 base can be used as magnetic temporary mount or fixed stud base for permanent installation.
- API 670 compliant: Approved for safety-critical turbomachinery case vibration protection.
- Drop-in replacement for existing 330500 series accelerometer points: No rework required for monitor scaling.
- Wide operating temperature range: Suitable for compressor, turbine and hot pump casing locations.
Application Fields
- Centrifugal compressors, turboexpanders and gas turbine casing vibration monitoring
- Steam turbine bearing housing absolute vibration measurement
- Gearbox high-frequency fault detection and condition monitoring
- Large process pumps, fans and blowers bearing housing vibration
- Offshore and refinery rotating machinery TSI systems
- LNG compression skids and refrigeration compressors
- Temporary vibration survey and permanent protection points
- Retrofit replacement for existing Bently 330500 accelerometer installations
Related Product Recommendations
- 330525-01: Integral cable version of 330500 accelerometer
- 167100-01: Bently accelerometer extension cable
- 3500/45: 3500 series accelerometer monitor module
- 3500/42M: Vibration and position monitor
- 3300/25: Legacy rack-based vibration monitor
- 146032-01: High temperature stud mount base variant
- 330400: Bently high-temperature accelerometer family
- Stainless steel mounting studs and thermal isolation pads
- System 1 condition monitoring software
- Shielded low-noise accelerometer cable
Installation & Maintenance
Installation
- For permanent critical protection points, preferred method is stud mounting; magnetic base (146031‑01) is mainly for temporary survey.
- Clean mounting surface thoroughly; flat, smooth surface maximizes high-frequency signal transfer and avoids resonance errors.
- Torque the sensor onto the mounting base to recommended torque value; over-tightening can damage internal piezo element.
- Route shielded accelerometer cable separately from high-power, servo and proximity probe coax cables to reduce electrical noise.
- Connect to matching Bently accelerometer monitor channel; configure unit (velocity mm/s or ips) and frequency band in software.
- Confirm hazardous area classification and cable sealing requirements for Class I Div 2 locations.
- Avoid mounting on thin, resonant sheet metal covers; select solid machine casting or bearing housing.
- Record sensor serial number, mounting location and baseline vibration signature after commissioning.
Maintenance
- During turnaround inspections, check connector pins for corrosion, cable jacket damage and base looseness.
- Review vibration spectrum and alarm status in System 1; rising high-frequency components indicate bearing degradation.
- Check for loose mounting first if readings are noisy or low amplitude; poor contact is the most common failure cause.
- Do not use magnetic base for permanent machinery protection circuits; magnetic mounts can shift under vibration.
- Keep spare matched assemblies (288055‑01 +146031‑01) for critical compressor/turbine points.
- After replacement, perform baseline spectrum capture and compare against historical reference before returning to service.
- Do not open the sensor housing; the piezo element is factory calibrated and cannot be adjusted on site.
- Store calibration data, alarm setpoints and spectrum baseline in machinery protection asset files.




