Description
Allen‑Bradley 1326AB-B420E-21 | Bulletin 1326AB Torque Plus Brushless AC Servo Motor
Product Description
1326AB-B420E-21 is a discontinued Rockwell Allen‑Bradley Bulletin 1326AB Torque Plus medium-inertia permanent magnet brushless AC servo motor. It is equipped with resolver feedback, IEC metric flange with keyway shaft, IP65 enclosure and convection cooling, designed to pair with 1394 SERCOS multi-axis servo system and 1391 digital servo drives. Delivering smooth torque output and high dynamic response, this motor is widely used for synchronized multi-axis motion on legacy printing, converting, packaging and cut-to-length machinery. This series has been end-of-life from Rockwell; available as surplus, refurbished spare for existing equipment maintenance.

1326AB-B420E-21
Technical Specifications
| Item | Parameter |
|---|---|
| Part Number | 1326AB-B420E-21 |
| Manufacturer | Allen‑Bradley (Rockwell Automation) |
| Series | 1326AB Torque Plus Brushless AC Servo Motor |
| Rated Power | 1.1 kW |
| Rated Speed | 3000 RPM @ 460VAC |
| Continuous Stall Torque | 5.0 Nm |
| Peak Stall Torque | 14.9 Nm |
| Rated Stall Current | 2.84 A |
| Supply Voltage | 380 / 460 VAC 3-Phase |
| Frame Size | 108 mm frame |
| Feedback Device | Resolver |
| Shaft & Mount | IEC metric flange, keyway shaft |
| Protection Class | IP65 |
| Cooling Method | Natural convection |
| Operating Temperature | 0℃ ~ +40℃ |
| Storage Temperature | -20℃ ~ +70℃ |
| Humidity | 5~95% RH non-condensing |
| Weight | ~4.8 kg |
| Status | Discontinued / EOL |
Compatibility & Installation Pitfalls
Compatibility
- Servo Drives: Allen‑Bradley Bulletin 1394 SERCOS servo system (1394C-SJT series), Bulletin 1391 digital servo drives
- Feedback: Resolver interface, must match resolver input port of servo drive
- Mechanical: Standard IEC 108mm metric flange, direct fit for original machine mounting bracket
- Cable: Matching AB 1326 series motor power cable + resolver feedback cable
- Variant note: -21 suffix = resolver feedback, no brake; variants with suffix -S2L/-M2L use encoder feedback and cannot directly substitute
Critical Installation Pitfalls
- Feedback mismatch risk: This unit uses resolver feedback. Cannot replace with encoder-feedback 1326AB variants without changing drive hardware and wiring.
- Shaft load limitation: Avoid excessive radial/axial overhang load on output shaft. Overload will damage bearings and resolver.
- Cable shielding requirement: Motor power and resolver feedback cables must be separate shielded cables. Do not bundle power and feedback wires together, which creates EMI noise and position drift.
- Shaft coupling alignment: Misaligned coupling causes vibration, bearing wear and premature motor failure. Perform laser alignment during installation.
- IP65 seal integrity: Check shaft seal and connector gaskets before installation. Damaged seals allow dust, oil and moisture ingress.
- LOTO mandatory before wiring: Lockout/Tagout drive power before connecting motor terminals; residual bus voltage can cause electric shock.
- Motor winding insulation test: For refurbished spare, perform megger insulation test before commissioning to detect hidden winding degradation.
- Direction & phase sequence: Incorrect 3-phase wiring leads to reverse rotation or unstable torque control; verify phase sequence carefully.
Standard Operating Procedure (SOP)
1. Pre-Installation Inspection & LOTO
- Verify part number 1326AB-B420E-21, inspect shaft, flange, connector and cable gland for physical damage. Rotate shaft manually to check for smooth rotation and no grinding noise.
- Lockout/Tagout servo drive 3-phase mains and confirm DC bus discharge.
- Prepare matching motor power cable, resolver feedback cable, shielded cable glands, coupling, alignment tools and megger tester.
2. Mechanical Mounting
- Mount motor to machine base, align coupling between motor shaft and driven load.
- Tighten mounting bolts to specified torque; complete coupling alignment to minimize radial offset and angular misalignment.
- Check shaft key fit and secure keyway set screw.
3. Wiring
- Connect 3-phase motor power and resolver feedback wiring strictly per schematic.
- Install shielded cables, terminate shield at drive side single-point grounding. Separate power and feedback cable routing.
- Confirm all connector gaskets are seated properly to preserve IP65 rating.
4. Power-Up & Commissioning
- Restore power to servo drive. Verify resolver signal reading on drive software.
- Perform phase rotation test with no load; jog motor at low speed to confirm correct rotation direction and smooth operation.
- Tune current loop, velocity loop and position loop gains. Monitor torque ripple and resolver feedback signal quality.
- Run dry cycle without load, then full load test; check motor temperature, vibration and noise.
- Test emergency stop and over-travel limit interlock functions.
5. Maintenance & Replacement
- Periodic maintenance: Inspect bearing noise, shaft seal leakage, connector tightness and cable insulation.
- Replacement procedure: Execute LOTO, disconnect power and resolver cables, remove coupling and mounting bolts, install new motor, re-align coupling, rewire, re-tune servo gains and run qualification test.
- Troubleshooting: Check resolver wiring continuity, insulation resistance and vibration data for bearing fault diagnosis.
Application Scenarios
- High-speed synchronized printing & converting machines
- Flying shear, rotary cut and cut-to-length processing lines
- Packaging machinery, carton forming and automated filling equipment
- Textile spinning and weaving synchronized motion systems
- Special-purpose automation assembly and material handling machines
Supporting / Matching Components
- Allen‑Bradley 1394C SERCOS servo drive (e.g.1394C-SJT10-A)
- Bulletin 1391 digital servo drive
- 1326AB series motor power cable and resolver feedback cable
- Flexible shaft coupling and shaft key
- EMI input filter for servo drive
- Dynamic braking resistor
- E-stop and safety limit switch assembly
- Cable shielded glands and grounding busbar
- Laser shaft alignment tool
- Megger insulation tester
15 Recommended Same-Series / Compatible Models (1326AB)
- 1326AB-B420E-S2L – 1.1kW, encoder feedback variant
- 1326AB-B420E-M2L – 1.1kW, medium resolution encoder
- 1326AB-B430E-21 – 1.4kW resolver feedback servo motor
- 1326AB-B515E-21 – 2.2kW resolver feedback motor
- 1326AB-B520E-21 – 2.9kW resolver feedback motor
- 1326AB-A410E-21 – 0.75kW low inertia resolver motor
- 1326AB-A420E-21 – 1.1kW low inertia resolver motor
- 1326AB-B410H-21 – 0.75kW resolver, high torque variant
- 1326AB-B720E-21 – 4.4kW resolver feedback motor
- 1326AB-B740E-21 – 7.5kW resolver feedback motor
- 1326AB-MOD-M40 – Encoder mounting adapter kit for B4xxx series
- 1326AB-B420E-21-K4 – 1326AB-B420E-21 with special shaft modification
- 1326AB–L – Low inertia modified variant
- 1326AB-B40H-21 – 0.55kW resolver servo motor
- 1326AB-B530E-21 – 3.7kW resolver feedback motor
FAQ
- Q: Can I replace 1326AB- directly with 1326AB-B420E-S2L? A: No. -21 uses resolver feedback; -S2L uses encoder. Drive feedback hardware and wiring must be changed, not plug-and-play.
- Q: Does this motor have built-in holding brake? A: No, 1326AB- is non-brake version. Brake variants have different part suffix.
- Q: Which drive is best match for this motor? A: Allen‑Bradley 1394C SERCOS system modules like 1394C-SJT10-A, also compatible with Bulletin 1391 drives.
- Q: What is the enclosure rating? A: IP65, suitable for factory floor environment; not for submerged or heavy wash-down applications.

