Bently Nevada 3500/15 106M1079-01 + 106M1081-01 Universal AC Power Supply Product Introduction
Product Overview
The Bently Nevada 3500/15, consisting of the 106M1079-01 front panel power supply module and the matching 106M1081-01 backplane Power Input Module (PIM), is a half-height universal AC power supply designed exclusively for the 3500 Machinery Protection System. As the core power backbone of the entire 3500 rack, it converts wide-range alternating current input into highly regulated, isolated DC outputs to power all internal monitoring, relay, and communication modules within the system .
This power supply pair is engineered for mission-critical industrial rotating machinery protection scenarios, delivering uninterrupted, clean power to vibration, displacement, temperature, and speed monitoring channels. It supports dual redundant power configuration, allowing two identical 3500/15 units to be installed in the dedicated left-side slots of the 3500 rack for 1+1 fault-tolerant operation. Either power supply can independently deliver full power to the entire rack, ensuring zero downtime for monitoring and protection functions even if one unit fails .
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer | Bently Nevada (Baker Hughes) |
| Part Number Combination | 3500/15 (106M1079-01 Front Panel + 106M1081-01 PIM) |
| Input Voltage | 85–264 VAC rms (universal global AC range) |
| Input Frequency | 47–63 Hz |
| Total Maximum Output Power | 460 W |
| DC Output Rails | +5 Vdc, ±15 Vdc, +24 Vdc |
| Full Rack Maximum AC Current Draw | 2.8 A rms |
| Form Factor | Half-height module, left-side dedicated rack slot installation |
| Redundancy Support | 1+1 dual-supply redundancy; lower slot = primary, upper slot = backup |
| Hot Swap Capability | Fully supported when redundant second power supply is operational |
| Operating Temperature Range | -30°C to +65°C (-22°F to +150°F) |
| Storage Temperature Range | -40°C to +85°C (-40°F to +185°F) |
| Relative Humidity | Up to 95% non-condensing |
| Efficiency | > 85% low-ripple, low-noise conversion |
| Certifications | CE, FCC, UL, ATEX, Class 1 Division 2 / Zone 2 hazardous area certified |
Core Features
- Universal Wide-Voltage Input: The 85–264 VAC input range fully accommodates global industrial grid standards and absorbs severe voltage fluctuations common in power plants, petrochemical facilities, and metallurgy sites, eliminating the need for region-specific power supply variants .
- Seamless Redundant Operation: When two power supplies are installed, the primary and backup units automatically balance load sharing. If the primary supply experiences an unexpected fault, the backup unit takes over the full rack load instantly with no interruption to monitoring logic or protection trip functions .
- Genuine Hot-Swappable Maintenance: With a redundant second power supply active, technicians can remove and replace a degraded 106M1079-01 + 106M1081-01 assembly without shutting down the 3500 rack or tripping the protected machinery, drastically reducing planned maintenance downtime .
- Built-In Protection & Diagnostics: Integrated over-current, over-voltage, over-temperature, and reverse-polarity protection circuits prevent damage to downstream precision monitoring modules. The front-panel “SUPPLY OK” LED provides immediate visual health status, and the module continuously sends power health alarm signals to the 3500 system rack interface for remote monitoring .
- Hazardous Area Compatibility: Certified for Class 1 Division 2 / Zone 2 locations, this power supply pair is fully qualified for deployment in explosive oil & gas, offshore platform, and chemical processing environments where standard commercial power supplies cannot be safely applied .
Installation & Compatibility Notes
- The 106M1079-01 front panel module and 106M1081-01 backplane PIM are strictly matched components for the universal AC version of the 3500/15 system. They cannot be intermixed with older high-voltage AC, low-voltage AC, or DC power PIM variants, as mismatched assemblies will fail to power on or blow internal fuses .
- The modules must only be installed in the dedicated leftmost power slots of the 3500 rack; they cannot be placed in general-purpose I/O slots used for monitoring or relay modules .
- Never attempt hot-swap replacement on a single-power 3500 rack configuration, as this will cause total system power loss and interrupt all machinery protection functions. Always confirm the redundant backup power supply is in normal “SUPPLY OK” status before performing any removal operation .
- This universal AC 3500/15 assembly is fully backward-compatible with all standard 3500 system racks (3500/05 chassis) and all 3500 series monitoring, communication, and relay modules, making it the preferred modern replacement for legacy 3500 power supply units .
Typical Applications
This power supply combination is the standard power backbone for Bently Nevada 3500 machinery protection systems deployed on critical rotating assets including steam turbines, centrifugal compressors, large fans, pumps, generators, and gearboxes across power generation, oil & gas, petrochemical, pulp & paper, and heavy industrial manufacturing facilities worldwide . It fully complies with API 670 industry standards for machinery protection systems, delivering the reliable, uninterrupted power required to prevent unplanned machinery trips and catastrophic equipment damage.




