Bently Nevada 3500/15-05-00 Universal AC Power Supply Assembly, Hot‑Swappable Redundant Power for 3500 Machinery Protection Rack, Composed of 106M1081-01 (AC PIM) + 106M1079-01 (Converter)
Technical Specifications
- Catalog Number: 3500/15-05-05-00
- Brand: Bently Nevada (Baker Hughes)
- Product Type: Half-height rack universal AC power supply assembly for 3500 TSI system
- Assembly composition: 106M1081-01 (Universal AC Input Module PIM) + 106M1079-01 (DC converter module)
- AC Input: 85–264 VAC, 47–63 Hz, universal wide-range input
- Output: Multiple regulated DC rails to 3500 backplane, supports fully populated 3500 rack
- Hot Swap: Yes, hot-swap supported under redundant power configuration
- Indicator: Front panel “SUPPLY OK” LED status
- Protection: Input surge, overvoltage, overcurrent, short-circuit, overtemperature protection
- Mounting: Leftmost dedicated dual half-height power slots of standard 3500 chassis
- Operating Temperature: -20 °C ~ +60 °C (-4 °F ~ +140 °F)
- Humidity: 5%–95% RH, non‑condensing
- Compliance: API 670, CE, EMC, Class I Div 2 hazardous area approval
- Lifecycle Status: Mature active spare part for legacy 3500 machinery protection racks
- Country of Origin: USA
- Weight (full assembly): ~1.8 kg
Key Features & Advantages
- Complete factory-defined AC power assembly: 3500/15-05-05-00 is the top order number representing the matched pair 106M1081-01 + 106M1079-01.
- Global universal AC input: Supports 110 VAC and 220 VAC plant mains without jumper setting changes.
- Redundant parallel operation: Two 3500/15 assemblies can run in parallel to provide uninterrupted power for safety-critical turbomachinery protection.
- Hot-swap capability: Can be replaced online when the second redundant power set remains healthy, no rack shutdown required.
- Built-in EMI filtering: Clean DC output reduces noise interference to proximity probes, accelerometer and position monitor low-level signals.
- System health reporting: Supply OK status can be read locally and in 3500 configuration software / System 1 for remote alarming.
- Clear part distinction: This is the newer universal AC version; different from old 3500/15 low voltage AC variant (127610-01 +125840-02), not cross-compatible.
- API 670 compliant: Accepted for compressor, turbine and pump safety protection systems.
Application Fields
- Gas turbine, steam turbine and centrifugal compressor machinery protection cabinets
- Refinery, pipeline, offshore and LNG rotating equipment TSI monitoring systems
- Power plant boiler feed pump, generator and large fan vibration protection racks
- Petrochemical expander, refrigeration compressor and critical process pump monitoring
- Steel mill, pulp & paper large rotating machinery condition protection
- Retrofit replacement for existing 3500 racks requiring universal AC power supply
- Safety instrumented machinery protection projects following API 670
Related Product Recommendations
- 106M1079-01: DC converter module (inside this assembly)
- 106M1081-01: Universal AC PIM input module (front of this assembly)
- 3500/15 DC version: 133292-01 + 133300-01
- 3500/42M: Vibration / position monitor module
- 3500/45: Accelerometer monitor module
- 3500/53: Relay output module
- 3500/92: Ethernet communication gateway
- 3500 rack chassis and backplane
- System 1 machinery condition monitoring software
- AC surge protection terminal block for power input
Installation & Maintenance
Installation
- This assembly occupies two adjacent half-height power slots on the far left of the 3500 rack; front slot for 106M1081-01, rear slot for 106M1079-01.
- Confirm AC input voltage within 85–264 VAC before energizing.
- Separate AC mains wiring from proximity probe coax, accelerometer and low-level sensor cables to reduce EMI.
- For redundant architecture, feed two independent AC power sources to two separate 3500/15 assemblies.
- After power-up, check the “SUPPLY OK” LED and verify power health status in the 3500 software.
- Do not mix this universal AC set with older generation 127610 /125840 series power modules; they are incompatible.
- Keep cabinet ventilation unobstructed to avoid thermal shutdown.
- Follow hazardous area installation rules for Class I Div 2 locations.
Maintenance
- During turnaround, inspect AC terminal tightness, cable jacket condition, dust buildup and LED status.
- Monitor power fault alarms in System 1; intermittent supply alarms are commonly caused by loose AC connections or component ageing.
- Perform periodic redundant switchover test by isolating one AC feed while the other supply remains online.
- Stock this as a complete matched assembly (3500/15-05-05-00) instead of stocking the two parts separately for easy replacement.
- Hot-swap operation must follow site LOTO and safety permit procedures.
- After replacement, verify all monitor channels, relay trip chains and communication links are stable.
- No field-serviceable internal components; module disassembly is not permitted.
- Record serial numbers, power topology and redundant test results in TSI asset records.




