Bently Nevada 3500/15-02-02-00 Universal AC Power Supply Module Product Introduction
Product Overview
The Bently Nevada 3500/15-02-02-00 is a dedicated half-height universal AC power supply module designed exclusively for the 3500 Machinery Protection System. As the core power infrastructure of the entire 3500 rack, it converts industrial AC mains input into multiple sets of highly stable regulated DC power, which is distributed to all monitoring modules, the TDI interface, and the backplane bus through the rack’s dedicated power distribution network. It is the foundational hardware that ensures continuous, reliable operation of the entire machinery protection system, even under harsh industrial power fluctuation conditions .
This module is fully compliant with API 670 industry machinery protection standards. It integrates advanced power factor correction, overvoltage/overcurrent protection, and full self-diagnostic functions. It supports dual redundant hot-swap deployment, eliminating the single-point failure risk of system power supply, making it the industry-standard power solution for critical rotating assets in heavy industrial facilities.
Core Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer | Bently Nevada (Baker Hughes) |
| Part Number | 3500/15-02-02-00 |
| Module Type | Half-height Universal AC Power Supply |
| Input Voltage Range | 85 VAC to 264 VAC universal wide-range AC input |
| Input Frequency | 47 Hz to 63 Hz |
| Output Power | 125 W maximum continuous output power |
| Output Voltage Rails | Multiple regulated DC outputs for all 3500 series modules |
| Power Factor | ≥ 0.95 with built-in active PFC circuit |
| Operating Temperature Range | 0°C to +60°C |
| Storage Temperature Range | -40°C to +85°C (-40°F to +185°F) |
| Relative Humidity | 5% to 95% non-condensing |
| Form Factor | Standard 3500 series half-height plug-in module |
| Hot Swap Support | Fully supported for online replacement without interrupting system operation |
| Redundancy Support | 1+1 dual redundant parallel operation with seamless automatic switchover |
| Certifications | CE, UL, CSA, ATEX, Class 1 Division 2 / Zone 2 hazardous area certified |
Key Features
- Universal Wide-Range AC Input: The 85–264 VAC wide input design allows the module to adapt to various industrial power grid conditions worldwide, eliminating the need for manual voltage selection or extra step-down transformers. The built-in active power factor correction (PFC) circuit ensures stable power output even under severe mains voltage fluctuations .
- Full Self-Diagnostic & Real-Time Status Reporting: The module continuously monitors all output voltages, internal operating temperature, and power health status in real time. It automatically transmits all diagnostic data to the 3500/22M TDI module through the backplane bus, enabling operators to view power supply health information directly in System 1 diagnostic software. The front-panel “Supply OK” LED provides intuitive visual status feedback for on-site technicians .
- Dual Redundancy Hot-Swap Architecture: Two identical 3500/15 power supplies can be installed in the dedicated leftmost two slots of the 3500 rack, operating in 1+1 redundant parallel mode. If one power supply fails, the other unit seamlessly takes over 100% of the system power load instantly without any power interruption, completely eliminating the single-point failure risk of the entire system power supply .
- High Efficiency & High Reliability Design: The advanced switching power supply topology delivers high energy conversion efficiency, reducing unnecessary heat generation inside the rack. The module is rated for long-term continuous operation in heavy industrial environments, ensuring decades of stable service life for critical machinery protection systems.
- Seamless System Integration: It is fully compatible with all 3500 series racks, monitoring modules, and TDI units. No extra configuration is required after installation, the module automatically synchronizes with the rack power distribution system and provides stable power for all connected units.
Installation & Compatibility Notes
- The two dedicated leftmost slots of the 3500 rack are exclusively reserved for 3500/15 power supplies. For redundant operation, install two compatible power supplies in these two upper and lower positions to ensure full system power redundancy .
- After energizing the system, always verify that the front-panel “Supply OK” LED is illuminated normally, and confirm that all installed 3500 monitoring modules receive stable power through the 3500 configuration software .
- During routine maintenance, regularly check the AC power input connections and the rack internal cooling ventilation conditions to ensure the power supply operates within the specified temperature range. If the system power diagnostics indicate a supply failure, perform hot-swap replacement of the faulty module immediately .
- This 3500/15-02-02-00 module is fully backward-compatible with all 3500/05 racks and all M-series monitoring modules, making it the ideal direct drop-in replacement for legacy 3500/15 AC power supply units in existing 3500 system deployments.
Typical Applications
This universal AC power supply module is widely deployed on critical rotating assets including large steam turbines, centrifugal compressors, gas turbines, generators, and high-speed reciprocating compressors across power generation, oil & gas, petrochemical, and heavy industrial facilities. It provides highly reliable, uninterrupted power for the entire 3500 machinery protection system, ensuring that the protection system remains fully operational even during industrial power grid fluctuations or single power supply unit failures, effectively preventing unplanned downtime and catastrophic equipment damage caused by power supply anomalies .




